| Series | KAP12T-1A |
| Model | KAP12T-1A |
| Type | DC/DC Converters |
| Brand | MORNSUN |
| Input Current (no-load) | 8mA (Vin=12V,Vo=1.2V,Io=0A) |
| Start-up Voltage | 4.2 VDC (0-100%Io) |
| Under-voltage Protection | 3 (0-100%Io) |
| Reverse Polarity at Input | Avoid / Not protected |
| Input Filter | Capacitance filter; Module on: Ctrl pin pulled high TTL (1.5VDC~VIN) |
| ENl | Module off: Ctrl pin pulled low to GND (0~0.5VDC); Input current when off: 50 uA |
| Output Voltage Accuracy | ±1% (Full load, input voltage range) |
| Linear Regulation | ±1% (Full load, input voltage range) |
| Load Regulation | ±1% (Nominal input voltage) (0% -100% load) |
| Ripple & Noise | 20mVp-p (nominal input voltage, full load) (20MHz bandwidth) |
| Temperature Coefficient | ±0.02%/℃ (Operating temperature -40℃ to +105℃) |
| Transient Response Deviation | ±100mV; Nominal input voltage, 25% load step change: mV |
| Transient Recovery Time | 100 us |
| Short-circuit Protection | Continuous, self-recovery |
| Operating Temperature | -40 to 105℃ (See Fig. 1) |
| Storage Temperature | -55–125℃ |
| Storage Humidity | Non-condensing: 5–95 %RH; Peak temperature ≤245℃, duration ≤60s |
| Reflow Soldering Temperature | max. over typ, 217℃ max |
| Switching Frequency | 1.4MHz (Full load, nominal input voltage) |
| MTBF | 10000 k hours (MIL-HDBK-217F@25℃) |
| Operating altitude | 2000 m |
| Vibration | 10-150Hz,–along X, Y and Z |
| Moisture Sensitivity Level (MSL) | Level typ, 3 max (IPC/JEDEC J-STD-020D.1) |
| Pollution Degree | PD typ, 3 max |
| Dimensions | 3 x 2.8 x 1.6 mm |
| Weight | 0.046g(typ.) |
| Cooling Method | Free air convection |
| Typical Characteristic | Curves; Fig. 1; Fig. 1 |
| 1. Typical application | Cin Cout; Output; (ceramic (ceramic R1 R2; voltage; capacitor capacitor; 0.6V 3kΩ /; KAP12T-1A; 1.8V 3kΩ 1.5kΩ; 10uF/25V 226k/16V; 3.3V 6.8kΩ 1.5kΩ; 5.0V 11kΩ 1.5kΩ; Table 1; R; Output vol tage : Vout 0 . 6 ( 1 1 ) |
| Fig. 3 Typical | application circuit R; 2 |
| 1. The required Cin and Cout | capacitors must be connected as close as possible to the terminals of the module; |
| 2. Refer to Table 1 for Cin and Cout | capacitor values. For certain applications, increased values and/or tantalum or low ESR electrolytic capacitors may also be |
| 3. Converter cannot be used for | hot swap and with output in parallel. |
| 2. For additional information | please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout |
| PCB Recommended | layout |
| KAP12T-1A series switching | frequency up to 1.4MHz, PCB layout has |
| a greater impact on product | performance, when designing the PCB, |
| please refer to the following | points. |
| Keep the component | layout as compact as possible. |
| Keep the input capacitors | Cin as close as possible to VIN and GND, |
| and Cin is within 3mm | of the product VIN and GND. |
| Keep the output capacitors | Cout as close as possible to VOUT and |
| GND, and Cout is within | 3mm of the product VOUT and GND. |
| Use wide and short | alignments for main power alignment. |
| Refer to the diagram on the | right for specific layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Tape/Reel packaging bag number: |
| 2. The maximum capacitive | load offered were tested at nominal input voltage and full load; |
| 3. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH with nominal |
| input voltage and rated output | load; |
| 4. All index testing methods in | this datasheet are based on our company corporate standards; |
| 5. We can provide product | customization service, please contact our technicians directly for specific information; |
| 6. Products are related to laws | and regulations: see Features and EMC; |
| 7. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |