| Series | K78(L)04-1000R3 |
| Model | K78(L)04-1000R3 |
| Type | DC/DC Converters |
| Brand | MORNSUN |
| No-load Power Consumption | 0.1mA typ, 1mA max (Positive output) |
| Reverse Polarity Input | Avoid / Not protected |
| Input Filter | Capacitance Filter |
| Output Voltage Accuracy | ±2 typ, ±3 max (100% load, input voltage range) |
| Linear Regulation | ±0.2% typ, ±0.4% max |
| Load Regulation | ±0.4 typ, ±0.6 max (1, Nominal input) (0%-100% load; 20MHz bandwidth; 20%-100% load, Nominal) |
| Ripple & Noise | 20mVp-p typ, 75mVp-p max; input: mVp-p |
| Temperature Coefficient | ±0.03%/℃ (-40℃ to +85℃) |
| Transient Response Deviation | ±5% (Nominal input, 25%-50%-25%, 50%-75%-50% load) |
| Transient Recovery Time | 0.1 ms typ, 1 ms max (change) |
| Short-circuit Protection | Continuous, self-recovery (Nominal input) |
| Operating Temperature | -40–+85℃ (See Fig. 1) |
| Storage Temperature | -55 to +125℃; Soldering spot is 1.5mm away from case for 10: ℃ |
| Case Material | Black plastic; flame-retardant and heat-resistant (UL94-V0); K7804-1000R3: 17.50 × 11.50 × 9.00 mm |
| Dimensions | K78L04-1000R3: 17.50 × 11.50 × 7.50 mm; K7804-1000R3: 3.8g (Typ.) |
| Weight | K78L04-1000R3: 2.1g (Typ.) |
| Cooling Method | Free air convection |
| Electromagnetic | compatibility (EMC) |
| Immunity | ESD IEC/EN 61000-4-2 Contact ±4KV perf. Criteria B |
| Typical Characteristic | Curve; Fig. 1 |
| 1. Typical application | circuit |
| 1 | 3 1 2 |
| V in | + Vo +Vin DC/D C -Vou t; DC /DC |
| C1 | C1 3; 2 C2 C2; GND GND |
| GN D | GN D; Typical application for negative output |
| Typical application | for positive output; Fig. 2 Typical application circuit |
| + Vin | + Vout |
| G ND C3 | G ND C1/C3 C2/C4; Part No; (ceramic capacitor) (ceramic capacitor) |
| LDM | 2 - Vout |
| Fig. 3 Typical application circuit | for dual output positive and negative |
| ①The required C1 and C2 (C3 and | C4) capacitors must be connected as close as possible to the terminals of the module. |
| ②Refer to Table 1 for C1 and C2 | (C3 and C4) capacitor values. |
| ③For certain applications, increased | C2/C4 values and/or tantalum or low ESR electrolytic capacitors may also be used instead. |
| ④When using configurations as | shown in figure 3, we recommended to add an inductor (LDM) with a value of up to 10μH which helps reducing mutual |
| ⑤Converter cannot be used for hot | swap and with output in parallel. |
| 2. For additional information | please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout; K7804-1000R3 (Potting SIP)Dimensions; K78L04-1000R3(Open Frame SIP)Dimensions |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Packaging bag number: |
| 58010116(K78L04-1000R3), | 58210021(K7804-1000R3); |
| 2. The max. capacitive load | should be tested within the input voltage range and under full load conditions; |
| 3. Unless otherwise specified, | data in this datasheet should be tested under the conditions of Ta=25°C, humidity<75%RH when inputting |
| nominal voltage and | outputting rated load; |
| 4. All index testing methods | in this datasheet are based on our company corporate standards; |
| 5. We can provide product | customization service, please contact our technicians directly for specific information; |
| 6. Products are related to | laws and regulations: see Features and EMC; |
| 7. Our products shall be | classified according to ISO14001 and related environmental laws and regulations, and shall be handled by |
| Mornsun Guangzhou | Science & Technology Co., Ltd. |
| Address: No. 5, Kehui St. 1, Kehui | Development Center, Science Ave., Guangzhou Science City, Huangpu District, Guangzhou, P. R. China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail:info@mornsun.cn www.mornsun-power.com |