| Series | KAP05T-3A |
| Model | KAP05T-3A |
| Type | DC/DC Converters |
| Brand | MORNSUN |
| Input Current (no-load) | 35 uA (Vin=5V,Vo=1.2V,Io=0A) |
| Reverse Polarity at Input | Avoid / Not protected |
| Input Filter | Capacitance filter; Module on: Ctrl pin pulled high(TTL (1.2~VIN) |
| ENl | Module off: Ctrl pin pulled low to GND (0~0.4VDC); Input current when off: 0.05 uA |
| Output Voltage Accuracy | ±1 typ, ±3 max (Full load, input voltage range) |
| Linear Regulation | 0.5% typ, 1% max (Full load, input voltage range) |
| Load Regulation | 1 typ, 2 max (Nominal input voltage) (0% -100% load) |
| Ripple & Noise | 30mVp-p typ, 60mVp-p max (nominal input voltage, full load) (20MHz bandwidth) |
| Temperature Coefficient | ±0.02%/℃ (Operating temperature -40℃ to + 85℃) |
| Transient Response Deviation | ±50mV typ, ±120mV max; Nominal input voltage, 25% load step change: mV |
| Transient Recovery Time | 100 us typ, 500 us max |
| Short-circuit Protection | Continuous, self-recovery |
| Operating Temperature | -40 to 85℃ (See Fig. 1) |
| Storage Temperature | -55–125℃ |
| Storage Humidity | Non-condensing: 5–95 %RH; Peak temperature ≤245℃, duration ≤60s |
| Reflow Soldering Temperature | max. over typ, 217℃ max |
| Switching Frequency | 2.2MHz (Full load, nominal input voltage) |
| MTBF | 2000 k hours (MIL-HDBK-217F@25℃) |
| Operating altitude | 2000 m |
| Vibration | 10-150Hz,–along X, Y and Z |
| Moisture Sensitivity Level (MSL) | Level typ, 3 max (IPC/JEDEC J-STD-020D.1) |
| Pollution Degree | PD typ, 3 max |
| Dimensions | 2.5 x 2.0 x 1.4 mm |
| Weight | 0.027g(Typ.) |
| Cooling Method | Free air convection |
| Typical Characteristic | Curves; Vo=3.3V Vo=1.2V; Fig. 1 |
| 1. Typical application | Output C1/C2; R1 R2; voltage (ceramic capacitor); 0.6V 100kΩ --; 1.2V 100kΩ 100kΩ; 1.8V 10uF/16V 150kΩ 300kΩ; 3.3V 68kΩ 15kΩ; 4.0V 68kΩ 12kΩ; Table 1 |
| Fig. 2 Typical | application circuit R; V 0 . 6 ( 1 1 ); O; R; 2 |
| 1. The required C1 and C2 capacitors | must be connected as close as possible to the terminals of the module; |
| 2. Refer to Table 1 for C1 and C2 | capacitor values. For certain applications, increased values and/or tantalum or low ESR electrolytic capacitors may also be |
| 3. Converter cannot be used for | hot swap and with output in parallel. |
| 2. For additional information | please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Tape/Reel packaging bag number: |
| 2. The maximum capacitive | load offered were tested at nominal input voltage and full load; |
| 3. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH with nominal |
| input voltage and rated output | load; |
| 4. All index testing methods in | this datasheet are based on our company corporate standards; |
| 5. We can provide product | customization service, please contact our technicians directly for specific information; |
| 6. Products are related to laws | and regulations: see Features and EMC; |
| 7. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |