| Series | K12T-10A |
| Model | K12T-16A-N |
| Type | DC/DC Converters |
| Brand | MORNSUN |
| Input Current (full load/no-load) | K12T-10A-P(N): 4340/70 mA; Nominal input voltage: mA; K12T-16A-P(N): 7020/70 mA; K12T-20A-P(N): 8865/90 mA; K12T-10A, K12T-16A: 8.3mA max |
| Start-up Voltage | 4.5 VDC (K12T-20A) |
| Under-voltage Protection | 6.0 (K12T-10A, K12T-16A) |
| Turn-off Voltage | 4.0 (K12T-20A) |
| Reverse Polarity Input | Avoid / Not protected |
| Hot Plug | Unavailable |
| Input Filter | Capacitance filter; K12T-10A-P, K12T-16A-P (Positive logic): Ctrl pin open or pulled high(Vin-2.5V ~ Vin ); K12T-10A-N, K12T-16A-N (Negative logic): Ctrl pin open or pulled low to GND (0 ~ 0.5 VDC) |
| Ctrl | K12T-20A-P (Positive logic): Ctrl pin open or pulled high(Vin-0.5V ~ Vin ); K12T-20A-N (Negative logic): Ctrl pin open or pulled low to GND (0 ~ 0.5 VDC); K12T-10A-P, K12T-16A-P (Positive logic): Ctrl pin pulled low to GND (0 ~ 0.5VDC); K12T-10A-N, K12T-16A-N (Negative logic): Ctrl pin pulled high (Vin-2.5V ~ Vin) (Module on; Module off) |
| 2. Unless otherwise | voltage. @specified, parameters in this table were measured under the 5VDC output |
| Output Voltage Accuracy | ±1.0 typ, ±2.0 max (Full load, nominal input voltage) |
| Linear Regulation | ±0.3% (Full load, input voltage range) |
| Load Regulation | ±0.4% (Nominal input) (0% -100% load) |
| Ripple & Noise | nominal input, 100% load: 65mVp-p typ, 100mVp-p max; K12T-10A, K12T-16A: 0.75–5.0 mVp-p (20MHz bandwidth) |
| Trim | VDC; K12T-20A: 0.6–5.0 VDC |
| Sense | 110 %Vo; K12T-10A: ±75 %Vo |
| Transient Response Deviation | Nominal input, 50%-100%-50%: mV; load step change, K12T-16A, K12T-20A: ±100mV; di/dt=2.5A/us, with external K12T-10A, K12T-16A,: mV |
| Transient Recovery Time | 470 µF polymer capacitors: 20 us; K12T-20A: us; K12T-10A: 320 us |
| Over-current Protection | Nominal input: %Io; K12T-16A, K12T-20A: 200 %Io |
| Short-circuit Protection | Continuous, self-recovery (Nominal input) |
| Temperature Coefficient | ±0.02%/℃ (100% load) |
| Operating Temperature | -40 to +85℃ (See Fig. 1) |
| Storage Temperature | -55–+125℃ |
| Storage Humidity | Non-condensing: 5–95 %RH; Peak temp. Tc ≤245℃, maximum duration |
| Reflow Soldering Temperature | time≤60s over 217℃. For actual application,; please refer to IPC/JEDEC J-STD-020D.1. application, |
| Switching Frequency | 300kHz (Full load, nominal input voltage input) |
| MTBF | 1000 k hours (MIL-HDBK-217F@25℃) |
| MSL | MSL3 (IPC/JEDEC J-STD-020D.1) |
| Dimensions | K12T-10A, K12T-16A: 33.00 x 13.50 x 8.30mm; K12T-20A: 33.00 x 13.50 x 9.90mm; K12T-10A, K12T-16A: 8.6g (Typ.) |
| Weight | K12T-20A: 9.2g (Typ.) |
| Cooling Method | Nature convection or forced convection |
| EMC Emissions | CE: Selected based on the actual 1000µF /35V; RE: input current in application 100µF /35V |