| Serie | URD48_YMD-10WR3 |
| Modell | URD480512YMD-10WR3 |
| Typ | DC/DC-Wandler |
| Marke | MORNSUN |
| Eingangsstrom (Volllast / Leerlauf) | 248/4 typ, 258/10 max mA (Nominal input voltage) |
| Reflektierter Brummstrom | 30 (Nominal input voltage) |
| Stoßspannung (max. 1 s) | -0.7–100 |
| Start-up Voltage | 18 VDC |
| Under-voltage Protection | 15.5 typ, 12 min |
| Eingangsfilter | Pi filter 3.5-12VDC); Module on: Ctrl pin open or pulled high (TTL 3.5-12VDC) |
| Ctrl | Module off: Ctrl pin pulled low to GND (0-1.2VDC); Input current when off: 3mA typ, 10mA max |
| Hot-Plug | Unavailable |
| Ausgangsspannungsgenauigkeit | Vo1: ±1 typ, ±3 max; Input voltage, any balanced load Vo2: ±3 typ, ±6 max; Full load, Input voltage variation from Vo1: ±0.3 typ, ±0.5 max (0%-100% load) |
| Lineare Regelung | %; low to high, dual output Vo2: ±2% typ, ±3% max; 1, dual output, Vo1: ±0.5% typ, ±1% max (0%-100% load) |
| Lastregelung | ±3 typ, ±6 max (balanced power Vo2) |
| Transient Recovery Time ① | 300 µs typ, 500 µs max; 25% load step change, nominal input voltage: µs |
| Transient Response Deviation | ±5% typ, ±8% max (①) |
| Temperaturkoeffizient | ±0.03%/℃ (Full load) |
| Ripple & Noise ② | 75 mV p-p typ, 150 mV p-p max (5%-100% load) |
| Überspannungsschutz | 110–160 %Vo |
| Over-current Protection ③ | 110–200 %Io (Input voltage range) |
| Short-circuit Protection ④ | Continuous, self-recovery |
| Isolation (Eingang–Ausgang) | VDC (Electric Strength Test for 1 minute with a leakage) |
| Isolation | 1500 VDC |
| Isolationswiderstand | Input-output resistance at 500VDC: 1000 MΩ |
| Isolationskapazität | 1000 pF (Input-output capacitance at 100kHz/0.1V) |
| Betriebstemperatur | -40 to +85℃ (See Fig. 1) |
| Lagertemperatur | -55–+125℃ |
| Lagerfeuchtigkeit | 5–95 %RH (Non-condensing) |
| Gehäusematerial | Aluminum alloy |
| Abmessungen | 25.40 × 25.40 × 11.70 mm |
| Gewicht | 13.0g (Typ.) |
| Cooling method | Free air convection |
| Electromagnetic | compatibility (EMC) |
| CE | CISPR32/EN55032 CLASS B (see Fig.3-② for recommended circuit) |
| RE | CISPR32/EN55032 CLASS B (see Fig.3-② for recommended circuit) |
| ESD | IEC/EN61000-4-2 Contact ±4kV / Air ±6kV perf. Criteria B |
| RS | IEC/EN61000-4-3 10V/m perf. Criteria A |
| Immunity EFT | IEC/EN61000-4-4 ±2kV (see Fig.3-① for recommended circuit) perf. Criteria B |
| Surge | IEC/EN61000-4-5 line to line ±2kV (see Fig.3-① for recommended circuit) perf. Criteria B |
| CS | IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A |
| Typical Characteristic | Curve; Fig. 1 (Vin=48V) |
| All the DC-DC converters of this | series are tested before delivery using the recommended circuit shown in Fig. 2. |
| Input and/or output ripple can | be further reduced by appropriately increasing the input & output capacitor values Cin and Cout and/or by |
| selecting capacitors with a | low ESR (equivalent series resistance). Also make sure that the capacitance is not exceeding the max. |
| capacitive load value of the | product.; Vou t(VDC) Cin Cout; 5 100µF/16V; 12 100µF/100V 22µF/25V; 24 22µF/50V; Fig. 2 |
| 2. EMC compliance | circuit; List of components:; Model Vin: 48VDC; Choose according to actual input; FUSE; current; MOV S14K60; C0 330µF/100V; C1/ C2 4.7µF/100V; C3/ C4 Refer to the Cout in Fig.2; LDM1 15uH; Fig. 3; CY1/ CY2/ CY3/ CY4 2.2nF/2000V |
| Notes: For EMC tests we use Part | ① in Fig. 3 for immunity and part ② for |
| emissions test. | Selecting based on needs. |
| 3. The products do not | support parallel connection of their output |
| 4. For additional | information please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout |