| Serie | K12MT-16A |
| Modell | K12MT-16A-N |
| Typ | DC/DC-Wandler |
| Marke | MORNSUN |
| Input Current(no-load) | 70mA (Nominal input voltage) |
| Start-up Voltage ① | 4.5 VDC |
| Reverse Polarity Input | Avoid / Not protected |
| Hot-Plug | Unavailable |
| Eingangsfilter | Capacitance filter; K12MT-16A-P (Positive logic): ON/OFF pin pulled high (3VDC ~ Vin) or open; Module on: ON/OFF pin pulled low to GND (-0.2VDC ~; 0.2VDC) or open (K12MT-16A-N (Negative logic)) |
| ON/OFF | ON/OFF pin pulled low to GND (-0.2VDC ~ |
| ② | K12MT-16A-P (Positive logic): mA; Module off: 0.2VDC) mA; K12MT-16A-N (Negative logic): ON/OFF pin pulled high (3VDC ~ Vin); Input current when off: 2mA |
| Ausgangsspannungsgenauigkeit | TRIM resistor with 0.1%: %; Input voltage range,: ±1%; tolerance: %; TRIM resistor with 1% tolerance: ±3% (0% -100% load) |
| Lineare Regelung | 4mV typ, 20mV max (Full load, input voltage range) |
| Lastregelung | 4 typ, 20 max (Nominal input voltage, 1) (0% -100% load; 20MHz bandwidth; nominal input voltage, 10%-100%) |
| Ripple & Noise ① | 50mVp-p typ, 100mVp-p max; load: mVp-p |
| Trim | 0.6–3.63 VDC |
| Sense function | 0.5V; Vo=0.6VDC: V; ±30V; Co=7*47µF + 9*330µF: V; Vo=1.2VDC: V; ±35V; Co=7*47µF + 4*330µF: V; Nominal input voltage,: V; Vo=1.8VDC: V |
| Transient Response Deviation | 50%-100%-50% load step: ±40mV; Co=7*47µF + 2*330µF: mV; change, di/dt=2.5A/us: mV; Vo=2.5VDC: mV; ±45mV; Co=7*47µF + 330µF: mV; Vo=3.3VDC: mV; ±50mV; Co=4*47µF + 330µF: mV |
| Kurzschlussschutz | Re-power on or Ctrl reset to recover (Nominal input voltage) |
| Temperaturkoeffizient | ±0.4%/℃ (100% load) |
| Betriebstemperatur | -40 to +85℃ (See Fig. 1) |
| Lagertemperatur | -55–+125℃ |
| Lagerfeuchtigkeit | Non-condensing: 5–95 %RH; Peak temp. Tc ≤245℃, maximum duration |
| Reflow Soldering Temperature ① | time≤60s over 217℃. For actual application,; please refer to IPC/JEDEC J-STD-020D.1. application, |
| Vibration | 10-150Hz,–along X, Y and Z |
| Schaltfrequenz | 600kHz (Full load, nominal input voltage) |
| MTBF | 61897 k hours (MIL-HDBK-217F@25℃) |
| MSL | MSL3 (IPC/JEDEC J-STD-020D.1) |
| Notes: ① This module is not | an assembly is attempted, components may fall off (recommended for assembly on the bottom side of a customer board. If such) |
| Abmessungen | 12.20 x 12.20 x 8.40mm |
| Gewicht | 2.5g (Typ.) |
| Kühlmethode | Nature convection or forced convection |
| Typical Characteristic | Curves |
| Unless otherwise specified, the | test input conditions in the figure are all Vin=12VDC.; Fig. 1 |
| Remote Sense | Application |
| 1. Remote sense | connection if not used |
| 1. If the sense function is not used | for remote regulation the user must connect the VS+(Sense) to VOUT and VS- to GND at the DC-DC converter pins |
| and will compensate for voltage | drop across pins only; |
| 2. The connections between sense | lines and their respective power lines must be kept as short as possible, otherwise they may be picking up noise, |
| interference and/or causing | unstable operation of the power module. |
| 2. Remote sense | connection used for compensation |
| 1. Using remote sense with long | wires may cause unstable output, please contact technical support if long wires must be used; |
| 2. We recommend using adequate | cross section for PCB-track layout and/or cables to connect the power supply module to the load in |
| order to keep the voltage drop | below 0.5V and to make sure the power supply's output voltage remains within the specified range; |
| 3. Note that large wire impedance | may cause oscillation of the output voltage and/or increased ripple. Consult technical support or |
| factory for further advice of sense | operation. |
| PGOOD recommended | circuit; Table 1; VIN 3.3VDC; R1 100kΩ; R2 25-500Ω; LED2 MS-PT2012ZGSC |
| 1. PGOOD is the power good detection | pin. When the product is working normally, PGOOD at a high impedance, and LED2 on. when the product is abnormal, |
| which means the voltage on the | Vred(FB) pin is not within ±10% of the 0.6V, PGOOD is pulled to low level (0V-0.75V), and LED2 off; |
| 2. PGOOD pin applied voltage is | 3.3V, maximum is 4V. |
| 1. Typical application | Table 1; Part No. Cin Co; Vo=0.6V 7*47µF+9*330µF |
| Cin | Co; Vo=1.2V 7*47µF+4*330µF; K12MT-16A; Vo=1.8V 100µF/35V 7*47µF+2*330µF; -P(N); Vo=2.5V 7*47µF+330µF; Fig. 2 Vo=3.3V 4*47µF+330µF |
| 1. The required capacitors Cin | and Co must be connected as close as possible to the terminals of the module, to ensure the stability of the |
| 2. To reduce the output ripple | furtherly, increased Co values and/or tantalum or low ESR polymer capacitors may also be used instead; |
| 3. Refer to Table 1 for Cin and | Co capacitor values; |
| 4. Converter cannot be used | for hot swap and with output in parallel. |
| 5. In order to reduce the | disturbance of large current to GND, the TRIM and ON/OFF pins should be designed with SIG_GND as the reference |
| point. SIG_GND has been | connected to GND in the product, and the application periphery does not need to be connected again. |
| 2. Trim function for output | voltage adjustment (open if unused); Table 3; VOUT (VDC) R (kΩ); T; 0.6 Open; 1.2 20; 1.8 10; 2.5 6.32; 3.3 4.44; Calculating Trim resistor (RT) values::; 12; R ( k Ω ) ; T V - 0 . 6; O |
| Fig. 4 TRIM resistor connection | (dashed line shows internal resistor; network) |
| Notes: 1. R : Resistance of Trim; | VOUT: The trim up voltage; |
| 2. If R = ∞ or Trim pin | open, VOUT = 0.6 VDC. |
| 3. For additional information | please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Packaging bag number: 58210174; |
| 2. The maximum capacitive | load offered were tested at input voltage range and full load; |
| 3. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH with nominal |
| input voltage, 3.3VDC | output voltage and rated output load; |
| 4. All index testing methods | in this datasheet are based on company corporate standards; |
| 5. We can provide product | customization service, please contact our technicians directly for specific information; |
| 6. Products are related to | laws and regulations: see Features and EMC; |
| 7. Our products shall be | classified according to ISO14001 and related environmental laws and regulations, and shall be handled by |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |