| Dòng sản phẩm | VCF4850HBO-1300WR3P-N |
| Mã hàng | VCF4850HBO-1300WR3P-N |
| Loại | Bộ chuyển đổi DC/DC |
| Thương hiệu | MORNSUN |
| Input Current (full load) | 28.5A max (Room temperature, Vin = 48 V) |
| No Load Input Loss | 9.6W typ, 14W max (Room temperature, Vin = 48V) |
| Surge Voltage(100msec. max.) | -0.5–100 (Room temperature) |
| Max input Voltage | 78 VDC (Room temperature) |
| Input Start-up Voltage | 33–35 (Vin = 48V , Intput Series) |
| Input Under-voltage Protection | 31–33 |
| Bộ lọc đầu vào | Pi filter |
| Cắm nóng | Unavailable |
| Module turn-on | 0–1.2 VDC (Room temperature) |
| Module turn-off | 3.3–5 (Room temperature) |
| Ctrl ① Input current ② | 0.3mA (Room temperature) |
| Input loss during shutdown | 1W (Room temperature) |
| Start-up Delay Time | 1 ms (All operating Temperaturer ange) |
| Output Current Range | 0–100 %Io |
| Độ chính xác điện áp đầu ra | ±1 typ, ±2 max (Room temperature,Vin = 36-75 V, 0%-100%Io) |
| Độ ổn định tuyến tính | ±0.2% typ, ±0.5% max (Room temperature,Vin = 36-75 V, 100%Io) |
| Độ ổn định tải | ±0.4 typ, ±1 max (Room temperature, Vin = 48 V, 0%-100%Io) |
| Transient Recovery Time | Vin = 48V, 25-75-25% Io, di/dt = 1A/μs: 300 µs typ, 500 µs max; Vin = 48 V, 25-75-25% Io, di/dt = 1 A/μs: ±1 µs typ, ±3 µs max |
| Transient Response Deviation | %; Vin = 48 V, 10-100-10% Io, di/dt = 1 A/μs: ±8% |
| Hệ số nhiệt độ | ±0.03%/℃ (100%Io) |
| Ripple & Noise ② | 40mVp-p typ, 500mVp-p max (Room temperature,Vin = 36-75 V, 0%-100%Io) |
| Trim | 25–55 V |
| Sense | 105 %Vo |
| Bảo vệ quá nhiệt | 110℃ typ, 125℃ max (Product sur PCB face max. temperature) |
| Bảo vệ quá áp | 58–60 V (Vin = 36-75 V) |
| Bảo vệ quá dòng | 28–36 A (Vin = 36-75 V) |
| Bảo vệ ngắn mạch | Hiccup, continuous, self-recovery (Vin = 36-75 V) |
| Start-up Time | 150 typ, 500 max (Vin = 48 V, Constant resistance load) |
| Output Voltage Rise Time | 100 ms typ, 150 ms max (Room temperature,Vin = 48 V,0%-100%Io) |
| Power-off hold Time | 5 (Room temperature,Vin = 48 V,0%-100%Io) |
| Cách ly (đầu vào–đầu ra) | 2250 VDC |
| Cách ly | VDC (Electric Strength Test for 1) |
| Isolation (Output–⏚) | 750 VDC (case) |
| Điện trở cách điện | Input-output, resistance at 500VDC: 100 MΩ |
| Điện dung cách ly | 5000 pF (Input-output, 100KHz/0.1V) |
| Nhiệt độ hoạt động | -40 to +85℃ |
| Nhiệt độ bảo quản | -55–+125℃ |
| Độ ẩm bảo quản | 5–95 %RH (Non-condensing) |
| Vật liệu vỏ | Aluminum alloy case |
| Dimension | 61.0×57.9×12.7 mm |
| Trọng lượng | 118.0g (Typ.) |
| Phương pháp làm mát | Free air convection cooling or forced air cooling |
| Typical Characteristic | Curve; Fig. 1 |
| 1. Typical application | circuit |
| The input voltage ranges | from 36 to 75VDC. When the input voltage exceeds 75VDC, |
| If the customer does not | use our EMC recommended circuits, the input must be connected with an electrolytic capacitor of at least |
| 470µF to suppress the potential | surge voltage at the input and ensure that the transient voltage does not exceed the value specified in the |
| In addition, the impedance | of both the input source and the load will interact with the impedance of the product, requiring the input |
| source to have a low impedance | characteristics. It is recommended that the minimum capacitance of the external input can be |
| guaranteed to be 470 µF at low | temperature. In some applications, performance can be enhanced by adding external capacitors. |
| The output end must be | connected with an electrolytic capacitor larger than the minimum capacitive load capacity to stabilize the |
| If it is required to further | reduce the input/output ripple, the external input/output capacitors Cin and Cout can be increased or a |
| capacitor with small series | equivalent impedance value can be selected, but the capacitance value should not be greater than the |
| maximum capacitive load of | the product.; Capacitors |
| +Vin | +Vo; Output Value Cin Cout (typ.) |
| Cin DC | DC Voltage; Cout; 50V 470uF/100V 1620uF/100V |
| -Vin | 0V; Fig. 2 It is recommended to carry out peripheral design according to the typical; ①; value of capacitive load, and use aluminum electrolytic capacitors or solid; electrolytic capacitors. |
| In addition to the 1. 5 5 25 1 0 5 127.44 701.67 25.55 10.22 100 Typical 5 5 25 1 0 6 155.16 701.67 43.75 10.22 100 Application 5 5 25 1 0 7 201.00 701.67 26.53 10.22 100 Circuit | capacitors, 10µF/100V tantalum capacitors and 0.1µF/100V ceramic capacitors should |
| be added to the ripple noise | test. It is recommended to use the following recommended peripheral circuit, and set the probe bandwidth to |
| 20MHz during the test. | Components Recommended Componen; C0 470µF/100V electrolytic capacitors; C1 0.1µF/100V ceramic capacitanc; C2 10µF/100V Tantalum capacitor; C3 1620µF/100V aluminum electrolytic; capacitor; Fig. 3 |
| 3. EMC compliance | circuit; Fig. 4; Components Recommended Component; MOV1/MOV2/MOV3 20D101K voltage sensitive resistor; C1/C4/C7/C10 680uF/100V aluminum electrolytic capacitor; C2/C3/C8/C9 4*4.7uF/100V; C5/C6 8*4.7uF/100V; 2*470uF/100V+680uF/100V; C11; aluminum electrolytic capacitor; CY1/CY2 2*4.7nF/Y2+1nF/Y1; CY3/CY4 2*4.7nF/Y2; CY5/CY6 4.7nF/Y2; CY7/CY8 2.2nF/Y1; CY9/CY10 4.7nF/Y2; CY11/CY12 4.7nF/Y2+2.2nF/Y1; 1.4mH, recommended to use MORNSUN; LCM1; P/N:FL2D-C5-142; 75uH, recommended to use MORNSUN; LCM2; P/N:FL2D-D0-250; 10uH, recommended to use MORNSUN; LCM3; P/N:FL2D-F0-100 |
| Phát xạ EMC | CE: CISPR32/EN55032 CLASS B (see Fig.4 for recommended circuit); RE: CISPR32/EN55032 CLASS B (see Fig.4 for recommended circuit) |
| Miễn nhiễm EMC | ESD: IEC/EN61000-4-2 Contact ±4KV/Air ±6KV (see Fig.5 for recommended circuit) (perf. Criteria B); RS: IEC/EN61000-4-3 10V/m (see Fig.4 for recommended circuit) (perf. Criteria A); EFT: IEC/EN61000-4-4 100kHz ±2kV (see Fig.4 for recommended circuit) (perf. Criteria B); Surge: IEC/EN61000-4-5 line to line ±2kV (see Fig.4 for recommended circuit) (perf. Criteria B); CS: IEC/EN61000-4-6 3 Vr.m.s (see Fig.4 for recommended circuit) (perf. Criteria A) |