| Serie | LBH150-13Bxx |
| Modell | LBH150-13B24 |
| Marke | MORNSUN |
| Eingangsspannungsbereich (AC) | 85–305 VAC |
| Eingangsspannungsbereich (DC) | 120–430 VDC |
| Input Frequency | 47–63 Hz; 115VAC: 2 Hz |
| Eingangsstrom | 1A max @230VAC |
| Einschaltstrom | 30A max @230VAC, Ta=25℃ |
| Leistungsfaktor | 0.99 typ, 0.96 min @50/60Hz, 115VAC/230VAC, Pout=150W |
| THD | Ta=25℃, Vin=115/230V, Pout=150W: 5%; Under-voltage protection start: %; 70–80%; (Input voltage drops from high to low): % |
| Input Under-voltage Protection | VAC; Under-voltage protection release: VAC; 75–85 VAC; (Input voltage rises from low to high): VAC |
| Recommended External Input Fuse | 3.15A/300V, slow-blow, required |
| Hot-Plug | Unavailable |
| Ausgangsspannungsgenauigkeit | ±2% (Full load range) |
| Netzregelung | ±0.5% (Rated load) |
| Lastregelung | ±1% (0% - 100% load) |
| Minimum Load | 0; 12V: 100 typ, 150 max; 24V: 200 typ, 250 max (20MHz bandwidth; (peak-to-peak value)) |
| Restwelligkeit und Rauschen | 28V: 200mV typ, 300mV max; Load at room temperature: mV; 48V: 300mV typ, 400mV max; >20%: mV; 54V: 300mV typ, 400mV max |
| Temperaturkoeffizient | ±0.02%/℃ |
| Stand-by Power Consumption | 2W typ, 4W max |
| Überbrückungszeit | 8 ms |
| Kurzschlussschutz | Hiccup, continuous, self-recover |
| Überstromschutz | 120% Io, self-recover after fault disappear; 12VDC output: ≤16VDC typ, (Hiccup) max disappear; 24VDC output: ≤32VDC typ, (Hiccup) max disappear |
| Überspannungsschutz | 28VDC output: ≤35VDC typ, (Hiccup) max; 48VDC output: ≤60VDC typ, (Hiccup) max; 54VDC output: ≤63VDC typ, (Hiccup) max (Maximum pulling current about 10mA, take HU- as) |
| No-load Output Of Auxiliary Source | 8–15 V; Over-temperature protection start (Aluminum: ℃; 105–115 (for reference ground (Internal resistor in series 1 kΩ); substrate temperature) until power off) |
| Over Temperature Protection | Over-temperature protection recovery: Reset input (0-0.1VDC),; ENA connect to HU- or Low-level (0-0.1VDC),; output is normal (0-0.1VDC), |
| ENA Remote Control ON/OFF | Enable control pin: (10-15VDC),; ENA disconnect or High-level (10-15VDC),; output turn off (10-15VDC), |
| Isolation (Eingang–Ausgang) | 3000 VAC |
| Isolation | VAC (Electric Strength Test for 1min.,) |
| Isolation (Input–⏚) | 1500 VAC (PE) |
| Isolation (Output–⏚) | 1500 VAC (PE) |
| Isolationswiderstand | Input - PE Test Voltage: 500VDC, Ta=25℃: 100 MΩ; Output - PE: 100 MΩ |
| Betriebstemperatur | -40 to +100℃ (Al-Substrate temperature) |
| Lagertemperatur | -40–+100℃ |
| Lagerfeuchtigkeit | Non-condensing: 95 %RH; Wave-soldering, Max. 10 seconds: 255–265 %RH |
| Löttemperatur | ℃; Manual-welding, Max. 5 seconds: 350–370℃; +90℃ to +100℃ (Al-Substrate temperature): 1.67 %/℃ |
| Power Derating | 85VAC - 100VAC: 1.33 %/VAC; BS EN/EN62368-1(Report) safety approved; |
| Safety Standard | Design refer to UL/IEC62368-1 |
| Schutzklasse | CLASS I; MIL-HDBK-217F@25℃: ≥300,000 h |
| MTBF | ≥1500,000 h (Telcordia SR-332@25℃) |
| Item | Standard (Operating Conditions) |
| Low Temperature Working | IEC60068-2-1 typ, GB2423.1, min (-40℃) |
| High Temperature Working | IEC60068-2-2 typ, GB2423.2, min (+85℃) |
| Low Temperature Storage | IEC60068-2-1 typ, GB2423.1, min (-40℃) |
| High Temperature Storage | IEC60068-2-2 typ, GB2423.2, min (+85℃) (Direction of Z axis: 120-2000Hz, 3.04mm, 10G;) |
| Sinusoidal Vibration | IEC60068-2-6 typ, GB2423.10, min (two direction of X, Y, axis: 20-2000Hz, 3.04mm, 20G) |
| Temperature Shock | IEC60068-2-14 typ, GB2423.22, min (-40℃ to +100℃) |
| Temperature Cycle | IEC60068-2-14 typ, GB2423.22, min (-40℃ to +50℃) |
| Hot and Humid | IEC60068-2-67 typ, GB2423.50, min (+85℃,85%RH) |
| Gehäusematerial | Black plastic, flame-retardant and heat-resistant (UL94V-0) |
| Dimension | Horizontal package: 63.14 x 60.60 x 12.70mm |
| Gewicht | Horizontal package: 140g (Typ.) |
| Kühlmethode | Using from the Al-Substrate to additional heat radiation of the radiator cooling |
| EMV-Emissionen | ; RE: CISPR32/EN55032 CLASS A |
| EMV-Störfestigkeit | Harmonic current: IEC/EN61000-3-2 CLASS A; ESD: IEC/EN61000-4-2 Contact ±6KV/Air ±8KV (perf. Criteria B); RS: IEC/EN61000-4-3 10V/m (perf. Criteria A); EFT: IEC/EN61000-4-4 ±2KV (perf. Criteria B); Surge: IEC/EN61000-4-5 line to line ±2KV/line to PE ±4KV (perf. Criteria B); CS: IEC/EN61000-4-6 10Vr.m.s (perf. Criteria A); Voltage variation: IEC61000-6-2/IEC 61000-4-11 (perf. Criteria B); Voltage interruption: IEC61000-6-2/IEC61000-4-11 (perf. Criteria C) |