| Серия | TTH0505-1T |
| Модель | TTH0505-1T |
| Бренд | MORNSUN |
| Inductance(L) ① | pin 1 to pin 3: 174.9–408.2 μH; pin 6 to pin 4: 216–504 μH; pin 1 to pin 3: 0.28 μH |
| DCR Isolation | Ω; pin 6 to pin 4: 0.52; Primary-Secondary Electric Strength Test for 1 minute: 5000 VAC; with a leakage current of 1mA max.: 6000 VDC |
| Patient Leakage Current | 2 μA max @250VAC,50/60Hz |
| Ёмкость изоляции | 6 pF (Primary-Secondary capacitance at 100kHz/0.1V) |
| Voltage-Time ② | 11 Vus |
| Влажность хранения | 95 %RH |
| Рабочая температура | -40 to +125℃ (③) |
| Storage Temperature ④ | -55–+125℃ |
| Пайка оплавлением | Peak temp.≤245℃, maximum duration time≤60s over |
| Temperature ⑤ | 217℃. |
| Transformer clearance & | 8 mm |
| Уровень чувствительности к влаге (MSL) | Level typ, 1 max (IPC/JEDEC J-STD-020D.1) |
| ③The temperature of | operating temperature range; (the transformer(ambient plus temperature rise) should be within the) |
| ⑤We suggest that | please refer to IPC/JEDEC J-STD-020D.1. (times of reflow soldering should not exceed twice, For actual application,) |
| Материал корпуса | Black plastic; flame-retardant and heat-resistant (UL94 V-0) |
| Габариты | 13.20 x 9.00 x 7.62 mm |
| Вес | 0.8g(Typ.) |
| Способ охлаждения | Free air convection |
| Material certification Material | UL No. |
| Wire | E234867, E211989 |
| Каркас катушки | E41429 |
| Varnish | E317427 |
| Phase Diagram | Turns Ratio (Np:Ns); Np-a:Ns-a Np-b:Ns-b; 1:1.1 (Typ.); Fig. 1 |
| Application Circuit | Table 1: Recommended parameters; MORNSUN; IC; SCM1201ATA; C1 1µF/25V; C2 1µF/25V; D1 40V/1A; D2 40V/1A; Fig. 2 |
| 1. If it is required to further reduce | input and output ripple, the capacitance of C1 and C2 can be increased properly if required, and should |
| be connected close to the pin | terminal of the module; |
| 2. In order to ensure the converter | can work reliably with high efficiency, the minimum load should not less than 1% rated load when it is |
| used. If the needed power is | indeed small, please parallel a resistor on the output side ( The sum of the efficient power and resistor |
| consumption power is not less | than 1%). |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Tube Packaging bag number: 58200075, Roll |
| Packaging bag number: | 58200074; |
| 2. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH, 100kHz and |
| 3. All index testing methods in | this datasheet are based on our company corporate standards; |
| 4. We can provide other analog | transformer customization service, please contact our technicians directly for specific information; |
| 5. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |