| Серия | TTF05xxM-1T |
| Модель | TTF0512M-1T |
| Бренд | MORNSUN |
| Inductance(L) ① | 引脚 1-2: 68–156 μH; TTF0503M-1T: μH; 引脚 3-4: 40–100 μH; 引脚 1-2: 68–156 μH; TTF0505M-1T: μH; 引脚 3-4: 90–210 μH; 引脚 1-2: 68–156 μH; TTF0509M-1T: μH; 引脚 3-4: 320–730 μH; 引脚 1-2: 68–156 μH; TTF0512M-1T: μH; 引脚 3-4: 530–1230 μH; 引脚 1-2: 68–156 μH; TTF0515M-1T: μH; 引脚 3-4: 810–1850 μH; 引脚 1-2: 68–190 μH; TTF0524M-1T: μH; 引脚 3-4: 2310–5390 μH; 引脚 1-2: 500 μH; TTF0503M-1T: μH; 引脚 3-4: 480 μH; 引脚 1-2: 500 μH; TTF0505M-1T: μH; 引脚 3-4: 700 μH; 引脚 1-2: 500 μH; TTF0509M-1T: μH; 引脚 3-4: 1300 μH |
| DCR Isolation | mΩ; 引脚 1-2: 500; 引脚 3-4: 1710; 引脚 1-2: 500; 引脚 3-4: 2100; 引脚 1-2: 500; 引脚 3-4: 2900; 3000 VAC; Primary-Secondary: 20 (TTF0512M-1T; TTF0515M-1T; TTF0524M-1T; Primary-Secondary Electric Strength Test for 1 minute; with a leakage current of 1mA max.; TTF0503M-1T、TTF0505M-1T、; TTF0509M-1T) |
| Ёмкость изоляции | capacitance at: pF; TTF0512M-1T、TTF0515M-1T、: pF; 100kHz/0.1V: 40 pF; TTF0524M-1T: pF |
| Voltage-Time ② | 10 uVs |
| Влажность хранения | 5–95 %RH (Non-condensing) |
| Рабочая температура | -40 to +125℃ (③ Including temperature rise) |
| Storage Temperature ④ | -55–+125℃ |
| Пайка оплавлением | Peak temp.≤250℃, maximum duration time≤60s over |
| Temperature ⑤ | 217℃. |
| ③The temperature of | operating temperature range; (the transformer(ambient plus temperature rise) should be within the) |
| ⑤We suggest that | please refer to IPC/JEDEC J-STD-020D.1. (times of reflow soldering should not exceed twice, For actual application,) |
| 封装尺寸 8.0 | x 4.95 x: 6.4mm |
| 重量 | 0.85g(typ.) |
| 冷却方式 | 自然空冷 |
| Material UL | No. |
| Wire | E234867 |
| Каркас катушки | E314793 |
| Phase Diagram | Output Voltage(VDC) Turns Ratio (Np:Ns) |
| 1 | 4 3.3VDC 25:20±0.5(TYP); 5VDC 25:29±0.5 (Typ.) |
| Np | Ns 9VDC 25:54±0.5 (Typ.); 12VDC 25:70±0.5 (Typ.) |
| 2 | 3; 15VDC 25:86±0.5 (Typ.); 24VDC 25:133±0.5 (Typ.); Fig. 1 |
| Application Circuit | D1; 1; +Vo; IC1; 4 3 4 D2 |
| VIN | VD2 VSS; 1 4; 5 2 C2 R8; VIN VSS D3 |
| C1 | 6 1 2 3 D4; VD1 VSS; 0V; 3 |
| GND | 2; Fig. 2; Table 1: Recommended parameters; 输出 9V 12V 15V 24V; IC1 SCM1208; C1 1µF/25V; D1 40V/1A; D2 40V/1A; D3 40V/1A; D4 40V/1A; C2 1µF/25V 1µF/50V; R8 27kΩ; 1; IC1 IC2 +Vo; 4 3 4 3 |
| 1. If it is required to further reduce | input and output ripple, the capacitance of C1 and C2 can be increased properly if required, and should |
| be connected close to the pin | terminal of the module. |
| 2. In order to ensure the converter | can work reliably with high efficiency, the minimum load should not less than 1% rated load when it is |
| used. If the needed power is | indeed small, please parallel a resistor on the output side ( The sum of the efficient power and resistor |
| consumption power is not less | than 1%). |
| 1. For customer systems that | are open-board products (with transformers exposed), it is recommended to apply conformal coating or apply |
| 2. If the customer's system is | an open-board product (with the transformer exposed), and there are scenarios of dropping or collision, it is |
| essential to apply conformal | coating or apply red glue for protection to the transformer, and do not directly impact the transformer. |
| Schematic diagram (The transformer | of applying conformal coating Schematic diagram of applying red glue; is completely wrapped) (Apply red glue to the pins of the transformer) |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Packaging bag number:58240124; |
| 2. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH, 100kHz and |
| 3. All index testing methods in | this datasheet are based on our company corporate standards; |
| 4. We can provide other analog | transformer customization service, please contact our technicians directly for specific information; |
| 5. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |