| Серия | CTTF0515-3T |
| Модель | CTTF0515-3T |
| Бренд | MORNSUN |
| Inductance(L) ① | pin 1 to pin 3: 178–534 μH; pin 6 to pin 4: 529–1586 μH; pin 1 to pin 3: 650 μH |
| DCR Isolation | mΩ; pin 6 to pin 4: 865; 3000 VAC (Primary-Secondary Electric Strength Test for 1 minute; with a leakage current of 1mA max.) |
| Ёмкость изоляции | 20 pF (Primary-Secondary capacitance at 100kHz/0.1V) |
| Voltage-Time ② | 11 Vus |
| Влажность хранения | 95 %RH (Non-condensing) |
| Рабочая температура | -40 to +125℃ (③) |
| Storage Temperature ④ | -55–+125℃ |
| Пайка оплавлением | Peak temp.≤245℃, maximum duration time≤60s over |
| Temperature ⑤ | 217℃. |
| Уровень чувствительности к влаге (MSL) | Level typ, 1 max (IPC/JEDEC J-STD-020D.1) |
| ③The temperature of | operating temperature range; (the transformer(ambient plus temperature rise) should be within the) |
| ⑤It is suggested that | please refer to IPC/JEDEC J-STD-020D.1. (times of reflow soldering should not exceed twice, For actual application,) |
| Материал корпуса | Black plastic; flame-retardant and heat-resistant (UL94 V-0) |
| Габариты | 12.50 x 8.70 x 5.90mm |
| Вес | 0.8g(Typ.) |
| Способ охлаждения | Free air convection |
| Material certification Material | UL No. |
| Wire | E234867 |
| Каркас катушки | E150608 |
| Phase Diagram | Turns Ratio (Np:Ns); Output voltage(VDC) Np-a:Ns Np-b:Ns; 15 1: 3.4 (Typ.); Fig. 1 |
| Application Circuit | Table 1: Recommended parameters; IC SCM1212-Q |
| VIN | T1 C1 1µF/25V; 1 6 |
| 3 | 4 +Vo |
| VD2 | VSS; C6 1µF/25V; Np-a D11 D12 |
| 2 VIN | 2 |
| C1 | Ns C6 R8; D11 40V/1A |
| 1 VD1 | VSS 5 Np-b; D21 D22 D12 40V/1A; 3 1 4 |
| IC | 0V; D21 40V/1A |
| GND | D22 40V/1A; Fig. 2; R8 51kΩ |
| 1. Full bridge rectifier circuit is | recommended for the secondary side of transformer |
| 2. If it is required to further reduce | input and output ripple, the capacitance of C1 and C2 can be increased properly if required, and should |
| be connected close to the pin | terminal of the module. |
| 3. In order to ensure the converter | can work reliably with high efficiency, the minimum load should not less than 1% rated load when it is |
| used. If the needed power is | indeed small, please parallel a resistor on the output side ( The sum of the efficient power and resistor |
| consumption power is not less | than 1%). |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Roll packaging bag number: 58200091; |
| 2. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH, 100kHz and |
| 3. All index testing methods in | this datasheet are based on our company corporate standards; |
| 4. We can provide other analog | transformer customization service, please contact our technicians directly for specific information; |
| 5. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |