| Serie | TDA51SCANHC |
| Modelo | TDA51SCANHC |
| Marca | MORNSUN |
| Dominant CANH output voltage | 2.9–4.5 |
| |V O(D) | | Figure 8 V = 0 V, R L =: 60 Ω V; TXD |
| Dominant CANL output voltage | 0.5–2 |
| V O(R) Recessive bus voltage | Figure 8 V = 2 V, R L =: 60 Ω 2–3 V; TXD; Figure 8 V = 0 V, R =: 60Ω 1.5–3 V; TXD L |
| V OD(D) Differential output voltage | Figure 8 V = 0 V, R =: 45Ω 1.3–3 V; TXD L; Figure 8 V = 3 V, R L =: 60 Ω –0.08–0.08; TXD |
| V OD(R) Recessive differential output | voltage; V = 3 V, No load: –0.5–0.05; TXD |
| V Common-mode output voltage | 2–3 V |
| V Common-mode output voltage peak | to peak: 60mV |
| I IH TXD High-level input current | V =2 V: 20 uA; TXD |
| I IL TXD Low-level input current | V =0.8 V: -20 uA; TXD |
| CMTI Common mode transient immunity | V = 0 V or V ; Figure: 150 kV/μs typ, 13 100 min; I CC |
| V IT+ Positive-going input threshold | voltage: 800mV typ, 900mV max; Figure 11 |
| V IT– Negative-going input threshold | voltage: 650mV typ, 500mV min; V hys Hysteresis voltage (V - V ): 125mV typ, 50mV min |
| IT+ IT | –; I OH = –4 mA, Figure 9: 4.8 typ, V – 0.8 min; CC |
| V OH High-level output voltage | I OH = –20 uA, Figure: 5 typ, 9 V – 0.1 min; CC; I OL = 4 mA, Figure 9: 0.2 typ, 0.4 max |
| V OL Low-level output voltage | I OL = 20 uA, Figure 9: 0 typ, 0.1 max |
| Input capacitance to ground | (CANH or |
| C I | V = 3 V, V I = 0.4 sin (4E6πt): 13 pF typ, + 2.5 V min |
| CANL) | TXD |
| C ID Differential input capacitance | V = 3 V, V I = 0.4 sin: 5 pF typ, (4E6πt) min; TXD |
| R ID Input resistance (CANH or | CANL) V = 3 V: 28–36 kΩ; TXD |
| R IN Differential input resistance | V = 3 V: 56–68 kΩ; TXD |
| R I(m) | V CANH = V CANL: –5%–5%; [1 – R / R ] × 100% |
| V Isolated power supply output | voltage No load, I =0mA: 4.65–5.47 V |
| ISO | ISO; V = 0 V, R = 60Ω, Dominant: 14–29; I L |
| VCC | V = V , Recessive: 14–29; I CC |
| ESD HBM | CANH, CANL pin to GND: ±5 kV |
| Isolation voltage | 5000 Vrms |
| Insulation characteristi Insulation resistance | 1 GΩ |
| Isolation capacitor | 3 pF |
| Transmission Characteristics | General test conditions and V =V = 5V, Ta: = 25℃ (unless otherwise specified).; CC ISO |
| Parameters | Conditions: Min.–Max. Unit |
| t | 35–130 ns |
| offTxD inactive | R = 60 Ω, C = 100 pF, see Figure 10 |
| t Differential output rise time | L L: 40 ns typ, 60 ns max |
| r | and Figure 12 |
| t Differential output fall time | 40 ns typ, 60 ns max |
| t Output rise time | 2.5 ns typ, 6 ns max |
| t Output fall time | 2.5 ns typ, 6 ns max |
| T Loop delay time | 110–210 ns |
| t Dominant time-out time | C =100 pF: 300–8000 us |
| TXD_DTO | L |
| Peso | 0.4(Typ.) g |
| TDA51SCANHC is a CAN of a style of separation | transceiver with the ability of differential: signal transmission between the bus and CAN protocol |
| controller, it the inner integration insulate DC/DC | power supply. which is compliant with ISO11898-2: standard. |
| Short-circuit protection: TDA51SCANHC has | current-limiting protection to prevent the: drive circuit from short-circuiting to positive and negative |
| supply voltages. The power dissipation increases | when a short circuit occurs. The short-circuit: protection function protects the driver stage from damage. |
| Over-temperature protection: TDA51SCANHC | has over-temperature protection. When: the junction temperature exceeds 160°C, the current in the |
| driver stage will decrease. Because the drive tube | is the primary energy consuming component,: current reduction can reduce power consumption and |
| reduce chip temperature. At the same time, the rest | of the chip remains functional. |
| state (blocking all network traffic). The timer is | triggered by the negative edge on pin TXD. |
| state. The timer is reset by the positive edge on pin | TXD. |
| Application circuit | Figure14. Typical application; Figure15. Type PCB layout |
| 1. The decoupling capacitors and energy storage | capacitor of VCC and GND1, VISO and GND2: should be placed as close the chip pins as possible to |
| the chip pins to reduce loop area and parasitic | inductance of PCB traces. General control should: be within 2mm. The decoupling capacitor is placed |
| close the chip, and the energy storage capacitor is | placed outside. As shown in Figre15-1.; Storage |
| Storage capacitor Decoupling | Decoupling; capacitor; capacitor; 10uF |
| 10uF capacitor | IC: IC |
| Not recommended | Recommended; Figure 15-1 |
| 2. The power line width should be designed at least | 0.5mm when wiring. |
| of parasitic inductance. | IC; IC |
| Component | Recommended part, value Component: Recommended part, value |
| R3 | 1MΩ D1, D2: 1N4007 |
| C1 | 1nF, 2kV D3: SMBJ30CA |
| T1 | ACM2520-301-2P R: 120Ω; terminal |
| GDT | B3D090L R1, R2: 2.7Ω/2W |
| protection device. Parameter description lists a set | of recommended circuit parameters, which: can be adjusted according to the actual application |
| situation. Also, when using the shielded cable, the | reliable single-point grounding of the shield: must be achieved. |
| V CC Power supply | 4.5–5.5 V |
| V I or V IC Voltage at any bus terminal (differential | mode) –12–12 V |
| V IH High-level input voltage (TXD) | 2–V +0.3; CC |
| V IL Low-level input voltage (TXD) | -0.3–0.8 V |
| V Differential input voltage | -7–7 V |
| ID | Driver -70 |
| I OH High-level output current | Receiver -2; Driver–70 |
| I OL Low-level output current | Receiver–2.5 |
| T A Operating temperature range | -40 to 125°C |
| T Junction temperature | -40 to 150°C |
| V CC = 5.5V, T A = | 125℃, RL= 60Ω; TXD |
| P Total power consumption | 900 mW |
| signal: | f=500kHz; Duty=50% |
| T Thermal shutdown temperature | 165°C |
| Signaling rate | 1000 kbps |