| Serie | TD341SCAN |
| Modelo | TD341SCAN |
| Marca | MORNSUN |
| Dominant CANH output voltage | 2.75–3.5 4.5 |
| |V O(D) | | Figure 8 V = 0 V, R L = 60; TXD |
| Dominant CANL output voltage | 0.5–1.5 2.25 |
| V O(R) Recessive bus voltage | Figure 8 V = 2 V, R L = 60: Ω 2–2.5 3 V; TXD; Figure 8 V = 0 V, t < t: ,; TXD: to(dom)TXD |
| V OD(D) Differential output voltage | 1.5–3 V; V =3.15 V to 3.45 V, RL = 50: to 65Ω; CC; Figure 8 V = 3.3V, R L =: 60 Ω –0.12–0.012; TXD |
| V OD(R) Recessive differential output voltage | V = 3.3 V, No load: –0.5–0.05; TXD |
| I IH TXD High-level input current | V =2 V: 20 uA; TXD |
| I IL TXD Low-level input current | V =0.8 V: -20 uA; TXD |
| R Internal TXD Pull up Resistor | 9.1 kΩ |
| V IT+ Positive-going input threshold voltage | 750 900 mV; Figure 11 |
| V IT– Negative-going input threshold | voltage: 500–650 mV; V hys Hysteresis voltage (V - V ): 120mV; IT+ IT –; I OH = –4 mA, Figure 9: V – 0.4 V–– 0.2; IO IO |
| V OH High-level output voltage | I OH = –20 uA, Figure 9: V – 0.1; IO; I OL = 4 mA, Figure 9: 0.2 0.4 |
| V OL Low-level output voltage | I OL = 20 uA, Figure 9: 0 0.1 |
| C I Input capacitance to ground (CANH or | CANL) V = 3.3 V, V I = 0.4 sin (4E6πt): + 2.5 V–13 pF; TXD |
| C ID Differential input capacitance | V = 3.3 V, V I = 0.4 sin: (4E6πt)–5 pF; TXD |
| R ID Differential input resistance | V =3.3V: 15–30 40 kΩ; TXD |
| R IN Input resistance (CANH or CANL) | V =3.3 V: 30–80 kΩ; TXD |
| R I(m) | V CANH = V CANL: –3%–0% 3%; [1 – R / R ] × 100% |
| IN(CANH) IN(CANL) | CANH, CANL pin to GND: ±15 kV |
| ESD HBM | Other pins: ±2 kV |
| EFT IEC61000-4-4:Perf. Criteria B | CANH, CANL and GND: ±2 kV |
| Surge IEC61000-4-5:Perf. Criteria B | CANH, CANL and GND(Common: Mode)–±2 kV |
| Isolation voltage | 5000 VDC |
| Insulation resistance | 1 GΩ |
| Isolation capacitor | 3 pF; V = V or 0 V, V = 1 kV,: transient |
| CMTI Common Mode Transient Immunity | TXD CC CM: 25 kV/us; magnitude = 800 V |
| Transmission Characteristics | General test conditions and V =V = 3.3V, Ta =: 25℃ (unless otherwise specified).; CC IO |
| Parameters | Conditions: Min. Nom.–Max. Unit |
| t Propagation delay TXD On to bus | active: 80–150 ns |
| t Propagation delay TXD Off to bus | inactive: 80–200 ns |
| offTxD | RL = 60 Ω, CL = 100 pF, see |
| Propagation delay RXD On to | receiver |
| t | Figure 10 and Figure 12: 60–300 ns |
| Propagation delay RXD Off to | receiver |
| Peso | 0.9(Typ.) g |
| voltage | voltage |
| TD341SCAN is a CAN of a style of separation | transceiver with the ability of differential: signal transmission between the bus and CAN protocol |
| controller, it the inner integration insulate DC/DC | power supply. which is compliant with ISO11898-2: standard. |
| Short-circuit protection: TD341SCAN has | current-limiting protection to prevent the drive: circuit from short-circuiting to positive and negative supply |
| voltages. The power dissipation increases when a | short circuit occurs. The short-circuit protection: function protects the driver stage from damage. |
| Over-temperature protection: TD341SCAN has | over-temperature protection. When the: junction temperature exceeds 160°C, the current in the |
| driver stage will decrease. Because the drive tube | is the primary energy consuming component,: current reduction can reduce power consumption and |
| reduce chip temperature. At the same time, the rest | of the chip remains functional.; Figure13. Typical Application Circuit; Figure14. Typical Application of PCB layout |
| In General, Vcc and VIo can be shorted(Figure 14) | .If the controller doesn't support 3.3V signal: input, it can power 5V for VIo. |
| When the module works in normal condition connect | the S foot to GND1.; Figure15. Port protection circuit for harsh: environments |
| Component | Recommended part, value Component: Recommended part, value |
| R3 | 1MΩ D1、D2: 1N4007 |
| C1 | 1nF, 2kV D3: SMBJ30CA |
| T1 | ACM2520-301-2P R: 120Ω; terminal |
| GDT | B3D090L R1、R2: 2.7Ω/2W |
| essential to add an adequate protection circuit to the | CAN signal ports to protect the system from: failure and maintain a reliable bus communication. |
| protection device. Parameter description lists a set | of recommended circuit parameters, which: can be adjusted according to the actual application |
| situation. Also, when using the shielded cable, the | reliable single-point grounding of the shield: must be achieved. |
| V CC Power supply | 3.15–3.3 3.45 V |
| V Power supply(Logic Side) | 2.375–5.5 V |
| V I or V IC Voltage at any bus terminal (differential | mode) –12–12 V |
| V IH High-level input voltage(TXD) | 2V |
| V IL Low-level input voltage(TXD) | 0.8V; Driver -70 |
| Receiver | V =3.3V -4; CC; Driver–70 |
| T A Operating temperature range | -40 to 105°C |
| I Recessive mode current | 20 35 mA |