| Serie | TD051S422H |
| Modell | TD051S422H |
| Marke | MORNSUN |
| DD2 | — — |
| Driver Characteristics | R = ∞, Refer to Figure: 7 2 V; L |
| |V | Differential drive output | R = 27 Ω (RS-485), Refer to: Figure 7 1.5 V |
| OD | L |
| Amplitude of change of | differential |
| Δ|V | | R = 27 Ω , Refer to Figure: 9–0.2 V |
| OD output | L |
| Steady state common | mode |
| V | Refer to Figure8: 3V |
| I Driver short-circuit current | -7V ≤ V ≤ 12V: ±110mA typ, ±200mA max |
| OS | OUT |
| VI Input High Level | — —: 2V |
| H | TXD, DE, R E |
| V Input Low Level | — —: 0.8V |
| IL | TXD, DE, R E |
| Forward differential input | threshold |
| Negative differential input | threshold |
| IT(–) voltage | V hysteresis voltage (V IT+ – V IT– ) −7 V ≤ VCM ≤ +12 V: 20mV |
| R Differential Input Impedance(A,B) | −7 V ≤ VCM ≤ +12 V: 96 kΩ |
| ID | V: = 12V–280 uA; — — OUT |
| I Input current (A,B pins) | DE = 0, R E= 0 |
| I | V: = -7V -100 uA; OUT; I = 20 μA, V − V = 0.2: V V − 0.1; OUT A B: DD1 |
| V RXD high output voltage | I = 4 mA, V − V = 0.2: V − 0.2 typ, V V − 0.4 min |
| OH | OUT A B: DD1 typ, DD1 min; I = −20 μA, V − V =: 0.2 V–0.1; OUT A B |
| V RXD low output voltage | I = −4 mA, V − V =: 0.2 V–0.4 |
| OL | OUT A B |
| Power supply and protection characteristics | 2.375 V ≤ V ≤ 5.5: V,; DD1 |
| I Logic side supply current | 6mA |
| DD1 | — —; Output without load, R E =: 0 V; Output without load,DE =: 5 V–10 mA; Output without load, DE =: 0 V–10 mA |
| ESD IEC/EN 61000-4-2(Contact) | A, B, Z, Y Pin to GND: ±4 kV |
| Perf. Criteria B | 6000 VDC; Leakage current <1mA,: t=1s; 4000 VAC |
| I-O | 5000 VDC; Leakage current <1mA,: t=60s; 3500 VAC; TXD = V or 0 V, VCM = 1 kV,: transient |
| CMTI common mode transient immunity | DD1: 150 kV/μs; magnitude = 800 V |
| Transmission Characteristics | General test conditions and V =V: =5V, Ta = 25℃ (unless otherwise specified).; DD1: DD2 |
| Parameters | Conditions: Min.–Max. Unit |
| transmission rate | 20 Mbps |
| t PLH , t PHL Drive Transfer | Delay: 50 ns typ, 90 ns max |
| Driver Differential | Output Delay; R = 54 Ω, C = C =: 100 pF, |
| t Offset | L L1 L2: 25 ns |
| SKEW (|t –t | |) Reference Figure: 9 |
| t r , t f Driver output rise delay, | fall delay: 6 ns typ, 25 ns max |
| t PLH , t PHL Receiver transmission | delay: 80 ns typ, 110 ns max |
| Receiver output rise | delay, fall C = 15 pF, Reference: Figure10; L |
| t r , t f | 5 ns typ, 10 ns max |
| Gewicht | 0.4(Typ.) g |
| The TD051S422H is a full duplex enhanced | RS485 transceiver. Each transceiver: contains a driver and a receiver. The transceiver is equipped with |
| state.The TD051S422H adopts a two-terminal | power supply, and the logic side: supports the conversion of 3.3V and 5V logic levels, and the whole |
| transceiver due to overloading or short-circuit. | transceiver from irreversible damage: caused by bus overload or short circuit.Receiver input filter: |
| differential signal. Therefore, the transmission | delay of the receiver is also caused by: this reason. |
| Bus Failure Protection: In general, the | bus receiver will be in an indeterminate: state when -220mV < A-B < -20mV. This phenomenon will occur when |
| EIA/TIA -This feature ensures that the receiver | output level is high even when the: bus differential voltage is 0V and complies with the EIA/TIA ±200mV |
| requirement.The bus load capacity (256 | point): standard RS485 receiver input impedance: is defined as 12 kΩ (unit load). A standard RS485 driver can |
| drive at least 32 load units. TD051S422H | bus receiver designed by 1/8 unit load, the: input impedance is greater than 96 kΩ. As a result, the bus allows |
| access to more transceivers (up to 256). | TD051S422H can also be mixed with the: standard RS485 transceiver with 32 unit loads (cumulative receiver |
| load cannot exceed 32 units). | — — |
| can be maintained for at least 600ns, the | transceiver will reliably enter into shutdown: mode.Drive output protection: TD051S422H internal integrated |
| pull-up and down resistors of the overall | network have a parallel value of 380Ω~420Ω: (0.2W).; Figure 15. Typical Pull-Up and Pull-Down: Resistor Connections; — — |
| TD051S422H SOIC | 16: TD051S422H–340/REEL |