| Serie | TD541S485H |
| Modell | TD541S485H |
| Marke | MORNSUN |
| Differential driver output | Driver; No load: 3.5V; |V |: 2.0 typ, 1.5 min; OD; R =100Ω, Figure 6: 2.0; L |
| Δ|V | for complementary | output |
| OD | ∆V: ±0.2V |
| states | OD |
| Common-Mode output voltage | V: 1–3 V; OC |
| OC | ΔV: -0.1–0.1 V |
| Output short-circuit current | I: ±110mA typ, ±250mA max; OS |
| Internal TXD Pull up Resistor | R: 5.1 kΩ; TXD |
| Internal DE Pull down Resistor | R: 5.1 kΩ; DE; Receiver |
| Positive differential input | V IT(+): –20 mV |
| threshold voltage | A B |
| Negative differential input | V IT(–): V –220 mV |
| IT+ | IT– A B |
| Differential input resistance(A, | R ID: V 96 kΩ; A B; V: =12V–250 uA; DE=0, RE =0, OUT |
| Input current (A, B) | I; I; CC V: -110 typ, = -7V -200 min uA; OUT; I = 20 μA, V − V =: 0.2 V V − 0.1; OUT A B: CC |
| RXD output high voltage | V OH; I = 4 mA, V − V =: V − 0.2 typ, 0.2 V V − 0.4 min; OUT A B: CC CC; I = −20 μA, V − V =: −0.2 V–0.1; OUT A B |
| RXD output low voltage | V OL; I = −4 mA, V − V =: −0.2 V–0.4; OUT A B |
| and safeguard characteristic | Power supply |
| Supply current | I: 15mA typ, 30mA max; CC; Between A, B 100Ω: load–80 mA |
| Working current | I: 1Mbps–105 mA; CC; Between A, B 54Ω load,: 20Mbps–120 mA; A, B to GND: ±15 kV |
| HBM | ESD; Other pin: ±2 kV |
| IEC61000-4-4 | EFT: ±2 kV |
| IEC61000-4-5 | SURGE: Mode)–±2 kV |
| Insulate voltage | 5000 VDC |
| Insulate impedance | VI-O: 1 GΩ |
| Insulate capacitance | 3 pF |
| Common mode transient | TXD = V or 0 V, V =: 1 kV,; CMTI: 25 kV/us |
| immunity | transient magnitude =: 800 V |
| Maximum data rate | -: 20 Mbps |
| 25℃, transmission rate = 1Mbps | Test conditions: |
| Driver propagation delay | T , T: 100 ns typ, 200 ns max; PHL PLH; |T T |: 7–100 ns |
| PHL PLH | PHL- PLH |
| Driver rise/fall time | T , T: 30–100 ns; R F |
| Receiver propagation delay | T , T: 50 ns typ, 150 ns max; PHL PLH; C = 15pF, Figure 8; L; |T T |: 15 ns typ, 50 ns max |
| PLH PHL | PHL- PLH |
| Receiver rise/fall time | T , T: 15 ns; R F |
| 25℃, transmission rate = | Test conditions: |
| Specifications | Physical |
| Parameters | Value Unit |
| Gewicht | ) typ, 0.9(Typ. min g |
| Performance Curves | Typical |
| 3. Driver output current vs. | Figure: Figure 4. Receiver output high voltage vs. Operating temperature; O |
| is a semi-duplex enhanced | TD541S485H: isolated power supply. In addition to an isolated power supply, each |
| contains a drive and a receiver. The | transceiver: failure protection function to ensure that the receiver output is high when |
| is open, short, or when the | the receiver input: 5VDC single power supply. The whole machine can monitor the overall |
| input filter: TD541S485H receiver | Receiver: input filter, the filter can greatly enhance the receiver's noise suppression |
| speed differential signal. Therefore, | ability to high: receiver is also caused by this reason. |
| protection: In general, when | Bus failure: receiver will be in an indeterminate state.This phenomenon occurs when |
| resistance. TD541S485H receiver | matches the: accurate, and the threshold voltage to the reference ground has a margin |
| which can ensure that even | of at least 10mV,: the receiver output level is high, and meets the requirements of |
| standard ±200mV. | EIA/TIA-485 |
| load capacity (256 point): standard | The bus: is defined as 12 kΩ (unit load). A standard RS485 driver can drive at |
| units. TD541S485H bus receiver (up to 256). TD541S485H | least 32 load: impedance is greater than 96 kΩ. As a result, the bus allows access to; more transceivers: RS485 transceiver with 32 unit loads (cumulative receiver load cannot; exceed 32 units). |
| SHUTDOWN mode: When high | Low power: input, the transceiver enters SHUTDOWN mode. When |
| reliably enter the off mode. | transceiver will |
| protection: TD541S485H | Drive output: (or overcurrent) protection module. In case of bus error or driver short |
| can limit the output current | circuit, the module; Figure 9. Typical application circuit: (Half-Duplex Network Topology); Figure 10. Type: PCB layout; Figure 11. Port protection circuit: for harsh environments |
| components and values: | Recommended |
| Component | Recommended part, value: Component Recommended part, value |
| R3 | 1MΩ: 2.7Ω/2W typ, R1, R2 min |
| C1 | 1nF, 2kV: SMBJ6.5CA typ, D1, D2 min |
| T1 | ACM2520-301-2P: SMBJ6.5CA typ, D3 min |
| GDT | B3D090L: 120Ω typ, R min; terminal |
| modules internal A / B lines come | As the: generally satisfy most application environments without the need for |
| protection devices. For harsh | additional ESD: such as motors, high voltage/current switches, lightning and similar |
| recommended that the user protects | however, we: additional measures and external components such as TVS tube, |
| inductors, Gas discharge tube, | common mode: the same single network Earth point. Figure 11 shows our |
| circuit diagram for such type of | recommended: values given in the table above. This recommendation is for reference |
| have to be adapted accordingly | only and may: in order to match the actual situation and application. |