| السلسلة | K12T-20A-P(N)-ST |
| الطراز | K12T-20A-P-ST |
| النوع | محولات DC/DC |
| العلامة التجارية | MORNSUN |
| Input Current (no-load) | 50mA (Nominal input voltage,Vo=0.6V) |
| Start-up Voltage | 4.5 VDC |
| Reverse Polarity Input | Avoid / Not protected |
| التوصيل أثناء التشغيل | Unavailable |
| مرشح الدخل | Capacitor filter open; K12T-20A-P-ST: TTL High (2VDC to 5.5VDC) or open; Module on: open; K12T-20A-N-ST: GND (0 to 0.8VDC) or open |
| Ctrl | K12T-20A-P-ST: GND Low level (0 to 0.8VDC) mA; Module off: mA; K12T-20A-N-ST: TTL High (2VDC to 5.5VDC) mA; Input current when off: 4.3mA typ, 6mA max |
| Notes: * 1.The Ctrl pin voltage is | K12T-20A-N-ST is a negative logic control (referenced to input GND. K12T-20A-P-ST is a positive logic control, and) |
| دقة جهد الخرج | Room temperature, input voltage range, 0%Io~100%Io,: %; ±1.5%; external TRIM resistance accuracy less than 0.1%: %; Room temperature, input voltage range, 0%Io~100%Io,: %; ±1.5% typ, ±2% max; external TRIM resistance accuracy less than 1%: %; V <2.5V: ±20%; O: % |
| Linear Adjustment Deviation | 25℃: mV; V ≥2.5V: ±30mV; O: mV; V <2.5V: ±20mV; O: mV |
| Load Adjustment Deviation | ±30 (V ≥2.5V) (25℃; O; 20MHz bandwidth; CIN=470uF(Polymer)+22uF*4 (ceramic)) |
| التموج والضوضاء | 30mVp-p typ, 60mVp-p max; C0=100uF*4 (ceramic)+330uF*2(Polymer)+1uF (ceramic): mVp-p |
| Trim | 0.6–5.5 VDC |
| معامل درجة الحرارة | 100% load: ±0.2%/℃; V =0.6: ±30%/℃; O: %/℃; V =1: ±35%/℃; O: %/℃; 25℃, Vin=12V,: %/℃; V =1.2: ±40%/℃; CIN=470uF(Polymer)+22uF*4 (ceramic), O: %/℃ |
| Transient Response Deviation | C0=100uF*4 V =1.8: ±45mV; O: mV; (ceramic)+330uF*2(Polymer)+1uF: mV; V =2.5: ±51mV; O: mV; (ceramic), 50%-100%-50% load, 2.5A/uS: mV; V =3.3: ±55mV; O: mV; V =5: ±60mV; O: mV |
| حماية من زيادة التيار | 25–35 A (Vin=12V) |
| حماية من قصر الدائرة | Continuous, self-recovery |
| درجة حرارة التشغيل | -40 to +85℃ (see Fig. 1) |
| درجة حرارة التخزين | -55–+125℃ |
| رطوبة التخزين | 5–95 %RH (Non-condensing) |
| تردد التبديل | Full load, nominal input voltage: 600 KHz; High-level input voltage: 2 KHz |
| SYNC | V; Low-level input voltage: 0.8V |
| SYNC Frequency | 650–1000 (Vin=12V) |
| MTBF | 61897 K hours (MIL-HDBK-217F@25℃) |
| MSL | MSL3 (IPC/JEDEC J-STD-020D.1) |
| 1. If the sense function is not | to VOUT and VS- to GND at the DC-DC (used for remote regulation the user must connect the VS+(Sense)) |
| 2. The connections between | as possible, otherwise they may be picking up (sense lines and their respective power lines must be kept as short) |
| 1. Using remote sense with long | wires must be used; (wires may cause unstable output, please contact technical support if long) |
| 2. We recommend using adequate | power supply module to the load inorder to keep the (cross section for PCB-track layout and/or cables to connect the) |
| voltage drop below 0.3V and to | range; (make sure the power supply's output voltage remains within the specified) |
| 3. Note that large wire impedance | Consult technical support or factory for further advice (may cause oscillation of the output voltage and/or increased ripple.) |
| PGOOD recommended | Table 1; VIN: 5VDC; R1: 100kΩ; R2: 25-500Ω; LED2: MS-PT2012ZGSC (circuit) |
| 1. PGOOD is the power good | at a high impedance, and LED2 on. when the (detection pin. When the product is working normally, PGOOD) |
| 1. 100 µF polymer capacitors | to ensure the stability of the module. ((C2) is required and should be connected close to the pin terminal,) |
| 2. To reduce the output ripple | capacitors may also be used instead. (furtherly, increased values and/or tantalum or low ESR electrolytic) |
| 2. Trim Function for | resistor network) (Fig. 2 TRIM resistor connection (dashed line shows internal) (Output Voltage Adjustment (open if unused)) |
| Recommended PAD | Pattern |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Packaging bag number: 58210344; |
| 2. The maximum capacitive | load offered were tested at input voltage range and full load; |
| 3. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH with nominal |
| input voltage, 5VDC output | voltage and rated output load; |
| 4. All index testing methods | in this datasheet are based on company’s corporate standards; |
| 5. We can provide product | customization service, please contact our technicians directly for specific information; |
| 6. Products are related to | laws and regulations: see Features and EMC; |
| 7. Our products shall be | classified according to ISO14001 and related environmental laws and regulations, and shall be handled by |
| Address: No. 5, Kehui St. 1, Kehui | development center, Science Ave., Guangzhou Science City, Huangpu District, Guangzhou, P. R. China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |