| Серия | DOP-107EG |
| Модель | DOP-107EG |
| Тип | Человеко-машинный интерфейс и сенсорные панели |
| Бренд | DELTA |
| (3) Description of each part | (5) Installation and wiring adjacent objects or walls. indoor use only). |
| Delta Electronics Inc, (Step 1:) | Step 2: |
| 33068, Taiwan | the screws until reaching the panel cutouts. Instruction Sheet (1) General precautions Thank you for purchasing this product. This instruction sheet provides information about the DOP-100 series HMI. Before using this product, please read through this instruction sheet carefully to ensure the correct use of the product. Please keep this sheet handy for quick reference whenever needed. Before finishing reading this sheet, please follow the instructions below: |
| liquids. (A) | Operation / display area Please refer to the wiring diagram when connecting the wires. plastic case. Do not touch the power supply when power is on, or it may cause electric shock. DOP-107BG torque: 6.17 lb-inch (0.7N-M) When the HMI displays a low power notification and requires a battery change, please contact your local distributor or Delta Customer Service Center for the replacement. Do not change the |
| MODE1 (Solid) | 24 - 12 7 - 8 mm 5 kg-cm (4.3 lb-in) |
| C (D) | COM2 / COM3 Stranded 24 - 12 7 - 8 mm 5 kg-cm (4.3 lb-in) (24 AWG wire min.) RS-232 |
| 4 (-) | rating of the cable must be greater than 75oC (167oF). |
| 5 (GND) | (4) Mounting dimensions DOP-107EG DOP-107EG COM2 port |
| MODE1 (MODE2) | MODE3 |
| COM Port (Pin) | COM2 COM3 COM2 COM3 COM2 COM3 |
| 9 (-) | D- - D- - RXD- Note: mark “-” means connection is not required. Unit: mm (inch) Operation temperature: 0oC to 50oC (32oF to 122oF) Storage temperature: -20oC to +60oC (-4oF to 140oF) (6) Hardware specifications |
| Model | DOP-107EG |
| Panel type | 7" TFT LCD (65535 colors) |
| Resolution | 800 x 600 pixels |
| Display (Backlight) | LED backlight (half-life under room temperature 25oC > 20,000 hours) *1 |
| Display range | 141.00 x 105.75 mm |
| Brightness | 450 cd/m² (Typ.) |
| CPU | ARM Cortex-A8 (800 MHz) |
| Flash ROM | 256 Mbytes |
| RAM | 256 Mbytes |
| Touchscreen | 4-wire resistive touchscreen > 10,000,000 operated |
| Buzzer | Multi-tone frequency (2 K – 4 KHz) / 80 dB |
| Network interface | 10/100 Mbps Auto sensing (with built-in isolated power circuit) *2 |
| USB | 1 USB slave Ver 2.0; 1 USB host Ver 2.0 |
| SD | SD * 1 |
| COM1 | RS-232 (supporting flow control) *2 Serial |
| communication (COM2) | RS-232 (supporting flow control) / RS-485*2 port |
| COM3 | RS-422 / RS-485*2 |
| Cooling method | Natural cooling CE / UL (please use shielding network cable and magnetic ring with the Approvals filter of 300 ohm / 100 MHz) |
| Panel waterproof level | IP65 / NEMA4 DC +24 V (-15% to +15%) (please use an isolated power supply) |
| Operation voltage*2 | Supplied by Class 2 or SELV circuit (isolated from MAINS by double insulation) |
| Leakage current | 500 VAC for 1 minute (between DC24V terminal and FG terminal) *2 |
| Power consumption | 8.4 W (Max)*3 |
| Backup battery | 3V lithium battery CR2032 × 1 About 3 years or more at 25oC Backup battery life (subject to operation temperature and condition) |
| Operation temperature | 0oC to 50oC (32oF to 122oF) |
| Storage temperature | -20oC to +60oC (-4oF to 140oF) 10% to 90% RH [0oC to 40oC], 10% to 55% RH [41oC to 50oC]; Operating environment pollution degree: 2 Conforms to IEC61131-2: continuous vibration 5 Hz - 8.3 Hz with amplitude Vibration resistance 3.5 mm; 8.3 Hz - 150 Hz with amplitude 1G Conforms to IEC60068-2-27: 11 ms, 15 G Peak, Shock resistance in X, Y, Z directions each for 6 times Dimension 184 x 144 x 50 (W) x (H) x (D) mm |
| Вес | Approx. 800 g Note: 1. The half-life of the back light is defined as the maximum luminance being reduced by 50% when the maximum drive current is supplied to the HMI. The life of LED backlight shown here is estimated at the room temperature of 25oC with ambient humidity. 2. The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute. 3. The HMI power consumption is the power consumed when the HMI is not connecting with other |
| (3) Parça Açıklamaları | (5) Montaj ve Kablolama boşluk olduğundan emin olun. Yüksek Renk ‧ Geniş Ekran ‧ Kullanıcı Dostu No.18, Xinglong Rd., Taoyuan City 33068, Taiwan kullanılmalıdır. Montaj için kullanılan panelin kalınlığı 5 mm’den az olmalıdır. Montaj Adımları: |
| Bilgi Dokümanı | Adım 1: HMI içine su geçirmez contanın takıldığına Adım 2: Montaj aparatlarını HMI’ın yuvalarına yerleştiriniz |
| (1) Önsöz | ve sonra panoya değene kadar vidaları sıkınız. yerleştiriniz. Bu ürünü satın aldığınız için teşekkür ederiz. Bu bilgi dokümanı DOP-100 serileri için bilgiler sağlar. Ürünü kullanmadan önce, doğru şekilde kullanım sağlamak için lütfen dokümanı tamamen okuyunuz. Ayrıca daha sonra ihtiyaç duyulduğunda kullanabilmek için bu dokümanı iyi muhafaza ediniz. Bu dokümanı okumayı bitirdikten sonra lütfen aşağıda yazılı olan talimatları uygulayınız. |