| Série | TTB05xxM-1T |
| Modelo | TTB0505M-1T |
| Marca | MORNSUN |
| Inductance(L) ① | pin 1 to pin 4: 68 μH typ, 56 μH min; TTB0503M-1T: μH; pin 2 to pin 3: 57 μH typ, 52 μH min; pin 1 to pin 4: 47 μH typ, 40 μH min; TTB0505M-1T: μH; pin 2 to pin 3: 68 μH typ, 56 μH min; pin 1 to pin 4: 520 μH; TTB0503M-1T: μH; pin 2 to pin 3: 500 μH |
| DCR Isolation | mΩ; pin 1 to pin 4: 450; pin 2 to pin 3: 520; 2250 VDC (TTB0505M-1T; Primary-Secondary Electric Strength Test for 1; minute with a leakage current of 1mA max.) |
| Capacitância de isolamento | 20 pF (Primary-Secondary capacitance at 100kHz/0.1V) |
| Voltage-Time ② | 10 uVs |
| Umidade de armazenamento | 5–95 %RH (Non-condensing) |
| Operating Temperature ③ | -40 to +125℃ |
| Storage Temperature ④ | -55–+125℃; Peak temp.≤250℃, maximum duration time≤60s over |
| Reflow Soldering Temperature ⑤ | 217℃. |
| ③The temperature of the | operating temperature range; (transformer(ambient plus temperature rise) should be within the) |
| ⑤We suggest that times of | please refer to IPC/JEDEC J-STD-020D.1. (reflow soldering should not exceed twice, For actual application,) |
| Dimensões | 5.90 x 3.20 x 2.4mm |
| Peso | 0.14g(Typ.) |
| Método de refrigeração | Free air convection |
| Material certification Material | UL No. |
| Wire | E234867 |
| Carretel | E314793 |
| Phase Diagram | Output; Turns Ratio (Np:Ns); Voltage(VDC); 3.3VDC 27:25±0.5(TYP); 5VDC 22:27±0.5 (Typ.); Fig. 1 |
| Application Circuit | Table 1: Recommended parameters; IC SCM1208; C1 1µF/25V; D1 40V/1A; D2 40V/1A; D3 40V/1A; D4 40V/1A; C2 1µF/25V; Fig. 2 R8 1kΩ |
| 1. If it is required to further reduce | input and output ripple, the capacitance of C1 and C2 can be increased properly if required, and should |
| be connected close to the pin | terminal of the module. |
| 2. In order to ensure the converter | can work reliably with high efficiency, the minimum load should not less than 1% rated load when it is |
| used. If the needed power is | indeed small, please parallel a resistor on the output side ( The sum of the efficient power and resistor |
| consumption power is not less | than 1%). |
| 1. For customer systems that | are open-board products (with transformers exposed), it is recommended to apply conformal coating or apply |
| 2. If the customer's system is | an open-board product (with the transformer exposed), and there are scenarios of dropping or collision, it is |
| essential to apply conformal | coating or apply red glue for protection to the transformer, and do not directly impact the transformer. |
| Schematic diagram (The transformer | of applying conformal coating Schematic diagram of applying red glue; is completely wrapped) (Apply red glue to the pins of the transformer) |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Packaging bag number: 58240108; |
| 2. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH, 100kHz and |
| 3. All index testing methods in | this datasheet are based on our company corporate standards; |
| 4. We can provide other analog | transformer customization service, please contact our technicians directly for specific information; |
| 5. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |