| Серия | TD551SCANH |
| Модель | TD551SCANH |
| Бренд | MORNSUN |
| Dominant CANH output voltage | 2.75–4.5 |
| |V O(D) | | Figure 18, V = 0 V, R L =: 60 Ω V; TXD |
| Dominant CANL output voltage | 0.5–2 |
| V OD(D) Differential output voltage | Figure 18, V = 0 V, R =: 60Ω 1.5–3 V; TXD L |
| V OD(R) Recessive differential output | voltage R =60Ω: –0.05–0.05 V; L |
| I IH TXD High-level input current | V =2 V: 20 uA; TXD |
| I IL TXD Low-level input current | V =0.8 V: -20 uA; TXD |
| CMTI Common Mode Transient | Immunity V = 0 or V =V: 180 kV/us; I I CC; |
| V IT+ Positive-going input threshold | voltage: 900mV |
| V IT– Negative-going input threshold | voltage: 500mV; V hys Hysteresis voltage (V - V ): 120mV |
| IT+ | IT – |
| V OH High-level output voltage | Figure 19; I OH = –4 mA: 4.8 typ, V – 0.4 min; CC |
| V OL Low-level output voltage | Figure 19; I OL = 4 mA: 0–0.4 V |
| C I (CANH or CANL) | 13 pF |
| R IN Input resistance (CANH or | CANL) V = 3 V: 10–100 kΩ; TXD |
| R I(m) | V CANH = V CANL: –5%–5%; [1 – R ) / R ] × 100% |
| V Isolated power output voltage | No load, I =0mA: 4.8–5.3 V |
| ISO | ISO; V = 0 V,R = 60 Ω, Access to: the main; I L: 75 typ, 120 max |
| I Supply Current(Logic side) | dynamic protection |
| VCC | V = V , hostage-taking: 23 typ, 30 max; I CC |
| HBM Mode | CANH, CANL inter-pin to: GND–±8 kV |
| Contact discharge Mode | CANH, CANL: ±4 kV; Input-Output, Leakage: current<1mA–6000 VDC; Rise time 3s, Fall time: 1s; Test time 1s: 4000 VAC |
| Insulation Isolation voltage | Input-Output, Leakage: current<1mA–5000 VDC |
| characteristics | Rise time 3s, Fall time: 1s; Test time 60s: 3500 VAC |
| Insulation resistance | 1 GΩ |
| Transmission Characteristics General | test conditions and V =V = 5V, Ta =: 25℃ (unless otherwise specified).; CC ISO |
| Parameters | Conditions: Min.–Max. Unit |
| t Propagation delay TXD On to bus | active: 75 ns typ, 110 ns max |
| t Propagation delay TXD Off to bus | inactive: 85 ns typ, 120 ns max |
| t Differential output signal rise | time: 30 ns typ, 60 ns max |
| t Differential output signal fall | time Figure 20: 30 ns typ, 60 ns max |
| f | R = 60 Ω, C = 100 pF |
| t Propagation delay RXD On to | receiver active L L: 85 ns typ, 130 ns max |
| t Propagation delay RXD Off to receiver | inactive: 85 ns typ, 130 ns max |
| t Output Signal Rise | 3 ns typ, 6 ns max |
| t Output Fall Time | 3 ns typ, 6 ns max |
| T T delay | 160 ns typ, 210 ns max |
| t Dominant time-out time | C =100 pF: 0.3–5 ms |
| TXD_DTO | L |
| Вес | 0.4(Typ.) g |
| Figure8. Quiescent Current vs. | Temperature: Figure9. Supply Current vs. Temperature |
| Figure10. Supply Current vs. Data | Rate Figure11. Drive: Differential Output Voltage Dominant vs. Supply |
| Figure12. Drive Differential Output Voltage Dominant | vs. Temperature Figure13.: Bus Output Voltage Recessive vs. Temperature |
| Figure14. Receiver Output High Voltage vs. | Temperature Figure15.: Propagation Delay from TXD to Bus Active vs. Temperature |
| Figure16. Propagation Delay from Bus to RXD | Active vs. Temperature Figure17.: Available Load Current Of VISO vs. Temperature |
| TD551SCANH is a CAN of a style of separation | transceiver with the ability of differential: signal transmission between the bus and CAN protocol |
| controller, it the inner integration insulate DC/DC | power supply.which is compliant with ISO11898-2: standard. |
| Short-circuit protection: TD551SCANH has | current-limiting protection to prevent the drive: circuit from short-circuiting to positive and negative supply |
| voltages. The power dissipation increases when a | short circuit occurs. The short-circuit protection: function protects the driver stage from damage. |
| Over-temperature protection: TD551SCANH | has over-temperature protection. When the: junction temperature exceeds 160°C, the current in the |
| driver stage will decrease. Because the drive tube | is the primary energy consuming component,: current reduction can reduce power consumption and |
| reduce chip temperature. At the same time, the rest | of the chip remains functional. |
| Application circuit | Figure24. Typical application circuit; Figure25. Typical Application of PCB: layout |
| 1. The decoupling capacitors (0.1uF)and energy | storage capacitor(10uF) of VCC and GND1, V: and GND2 should be placed as close the chip pins as; ISO |
| possible to the chip pins to reduce loop area and | parasitic inductance of PCB traces. General: control should be 0.35mm. The decoupling capacitor is |
| placed close the chip, and the energy storage capacitor | is placed outside. As shown in Figure: 25-1. |
| 0.1uF | 10uF 0.1uF |
| 10uF | IC: IC |
| 不推荐 | 推荐; Figure 25-1 |
| parasitic inductance. | IC; IC |
| Not Recommended | Recommended; Figure 25-2; Figure26. Port protection circuit for harsh: environments |
| Component | Recommend part, value Component: Recommend part, value |
| R3 | 1MΩ D1、D2: 1N4007 |
| C1 | 1nF, 2kV D3: SMBJ30CA |
| T1 | ACM2520-301-2P R: 120Ω; terminal |
| GDT | B3D090L R1、R2: 2.7Ω/2W |
| essential to add an adequate protection circuit to the | CAN signal ports to protect the system: from failure and maintain a reliable bus communication. |
| device. Parameter description lists a set of Recommend | circuit parameters, which can be adjusted: according to the actual application situation. Also, |
| when using the shielded cable, the reliable single-point | grounding of the shield must be achieved. |
| V CC Power supply | 4.5–5.5 V |
| V I or V IC Bus input pin withstand voltage (differential | mode) –58–58 V |
| V IH TXD Insulation characteristics | 2–5.5 V |
| V IL TXD low level output voltage | 0–0.8 V |
| T A Operating temperature range | -40 to 125°C |
| T J Junction temperature T | -40 to 150°C |
| T Thermal shutdown temperature | 165°C |
| Signaling rate | 5000 kbps |