| Série | DVP-EH |
| Modèle | DVP-EH2 |
| Type | API et contrôle de mouvement |
| Marque | DELTA |
| Model Name (Outline) | Function Explanation EH2 MPU built in COM1 (RS-232) and COM2 (RS-485). When connecting DVP-F232 RS-232 to PC or other peripheral, such as MODEM, by using COM2, you (RS-232 card) can use this extension card. The communication function is the same as |
| Terminal Layout (DB-9 | COM2 except communication interface, i.e. there are Slave mode and |
| male) | Master mode for you to choose. Note: PLC will set that COM2 is occupied by RS-232 card and built-in COM2 (RS-485) function will be invalid after GND |
| Tx (7) | PC V. High: high potential, i.e. logic 1 |
| or | (RS-232) e xte ns io n c a rd for DVP EH MP U |
| or HMI. | HMI For EH3 MPU, it will be COM3 card and either slave or master mode can be used. Application example for connection in Slave mode |
| PLC COM 2 (PC RS-232) | PLC COM2/ De lt a HMI PLC COM2/ |
| 3 Tx | Tx 3 |
| 3 Tx (Tx 3) | 3 Tx Tx 2 |
| 7 (7) | 7 7 7 6 |
| 8 (8) | 8 8 8 8 |
| 6 (6) | 6 6 6 20 |
| 5 GND S.G.5 (5 GND S.G.5) | 5 GND S.G.7 |
| 1 (1) | 1 1 1 4 |
| 4 (4) | 4 4 4 5 |
| 9 (Rl.) | 9 9 9 9 |
| Terminal Layout | COM2 is occupied by RS-422 card and built-in COM2 (RS-485) function will be invalid after inserting this card. Refer to following for system connection. Tx+: transmission |
| Tx- Tx-: transmission (1 Tx+) | Rx+ 2 6 RT S- De lta HMI DOPA s e rie s : RS-422 is at COM2, and need to set to MODE 2, |
| Rx+ (-) (2 Tx-) | Rx- 1 7 RT S+ R e fe r to fo llo win g fo r s e ttin g : |
| 3 Rx+ (Tx+ 3) | 8 CT S+ |
| Rx- (4 Rx-) | Tx- 4 9 CT S- MODE 1: RS-232 GND Rx+: receive (+) MODE 2: RS-422 MODE 3: RS-485 |
| Rx-: receive (-) | For EH3 MPU, it will be COM3 card and either slave or master mode can be used. There are 2 analog input points supported by F2AD card and their |
| Terminal layout (Analog signal) | DC 0~+10V DC 0~20mA |
| 0~10V | V0+ CH0 |
| Resolution (12bit) (2.5mV (10/4000)) | 10uA (20/2000) I0+ |
| 0~10V (V1+) | Input impedance 40KΩ 250Ω CH1 |
| Voltage input COM | D1118 setting (≧K150, unit: ms) conversion |
| 0~20mA (I1+) | 10V 20m A current input voltage input Current input COM |
| Digital value (Current value) | D1056 (CH0) D1057 (CH1) Voltage input signal limit: output |
| less than 12VDC (Inputting (Average value) | D1110 (CH0) D1111 (CH1) negative voltage is banned) User can get A/D conversion value saved in special D by reading special D Current input signal limit: that corresponds to current value or average value. D1118 setting is every |
| less than 30mA (Inputting | update time of current value of digital value output. negative current is banned) DVP-256FM(for EH2 series)/DVP-512FM(for EH3 series) is a data backup memory card. There is a switch on it and PLC will check the state of this memory data read/write action will be valid when switch is On. NOTE: DVP-512FM is black cover and DVP-256FM is white cover. There are 2 analog output points supported by F2DA card and their |
| CH0 I0+ (Analog signal) | DC 0~+10V DC 0~20mA |
| V1+ | 0~+10V |
| CH1 I1+ (Output impedance) | ≦ 0.5Ω ≧ 1MΩ COM Voltage output |
| Update time for conversion | D1118 setting (≧K5, unit: ms) Output voltage ≧ 1KΩ |
| 10V | 20mA |
| V0+ (voltage) | cur rent CH0 |
| 0~20mA (0) | 4000 4000 |
| I1+ (digital input) | digital input COM Current output User can move value to D1116 (CH0) or D1117 (CH1) to get correspondent |
| output load: 0~500Ω | output voltage by using instruction MOV. When two built-in COM1 (RS-232) and COM2 (RS-485) are not enough for DVP-F232S use, you can add one COM by this card (number is 3 and is called COM3. (RS-232 card) There are two interfaces, RS-232 and RS-485, for you to use. Its general |