| Serie | CTTF10X6-2T |
| Modelo | CTTF10X6-2T |
| Marca | MORNSUN |
| Inductance(L) ① | pin 1 to pin 3: 880–2640 μH; pin 6 to pin 4: 680–1570 μH; pin 1 to pin 3: 0.65–1.7 μH |
| DCR | mΩ; pin 6 to pin 4: 0.6–1.6 mΩ; Primary-Secondary Electric Strength Test for 1 minute: mΩ |
| Tensión de aislamiento | 3500 VAC; with a leakage current of 1mA max.: VAC |
| Resistencia de aislamiento | Primary - secondary, insulation voltage at500VD: 1000–∞ MΩ |
| Capacidad de aislamiento | 20 pF typ, 50 pF max (Primary-Secondary capacitance at 100kHz/0.1V) |
| Voltage-Time ② | 11 Vus |
| Humedad de almacenamiento | 5–95 %RH (Non-condensing) |
| Operating Temperature ③ | -40–+125℃ |
| Storage Temperature ④ | -55 to +125℃ |
| Material de la carcasa | Black plastic; flame-retardant and heat-resistant (UL94 V-0) |
| Dimensiones | 12.50 x 8.70 x 5.90mm |
| Peso | 0.92g(Typ.) |
| Método de refrigeración | Free air convection |
| Material certification Material | UL No. |
| Wire | E234867 |
| Bobina | E150608 |
| Phase Diagram | Turns Ratio (Np:Ns); Output voltage(VDC) Np-a:Ns-a Np-b:Ns-b; 6.5VDC 1:0.8 (Typ.); Fig. 1 |
| Application Circuit | Table 1: Recommended parameters; IC SCM1209; C1 1µF/25V; R0 10Ω; D1 40V/1A; D2 40V/1A; C2 1µF/25V; R8 5.1kΩ; Fig. 2 |
| 1. If it is required to further reduce | input and output ripple, the capacitance of C1 and C2 can be increased properly if required, and should |
| be connected close to the pin | terminal of the module. |
| 2. In order to ensure the converter | can work reliably with high efficiency, the minimum load should not less than 1% rated load when it is |
| used. If the needed power is | indeed small, please parallel a resistor on the output side ( The sum of the efficient power and resistor |
| consumption power is not less | than 1%). |
| Dimensions and | Recommended Layout |
| 1. For additional information | on Product Packaging please refer to www.mornsun-power.com. Tube Packaging bag number: 58200091, Roll |
| packaging bag number: | 58210038; |
| 2. Unless otherwise specified, | parameters in this datasheet were measured under the conditions of Ta=25℃, humidity<75%RH, 100kHz and |
| 3. All index testing methods in | this datasheet are based on our company corporate standards; |
| 4. We can provide other analog | transformer customization service, please contact our technicians directly for specific information; |
| 5. Our products shall be classified | according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified |
| Address: No. 8 Nanyun 4th Road, | Huangpu District, Guangzhou, China |
| Tel: 86-20-38601850 | Fax: 86-20-38601272 E-mail: info@mornsun.cn www.mornsun-power.com |