| Serie | MBP4803SO-2A |
| Modelo | MBP4803SO-2A |
| Tipo | Convertidores DC/DC |
| Marca | MORNSUN |
| Input Current (full load / no load) | 186/8 mA (Nominal input voltage) |
| Starting Voltage | 42 VDC; Output power range: VDC |
| Input under-voltage protection | 33 typ, 31 min |
| Module open | Ctrl pin open or pulled high TTL (4.5-12VDC); Full input voltage range, full output: (4.5-12VDC) |
| Ctrl ① Module shutdown | Ctrl pin pulled low to GND (0-1.2VDC); voltage range: (0-1.2VDC) |
| Static working current ② | 10 uA typ, 30 uA max |
| No-load Output Voltage | Input voltage range: 5.5 VDC; Input voltage range, Works in constant current: VDC |
| Output Constant Current Accuracy ① | 1.8–2.2 A; mode: A |
| Output Over-Voltage Protection | Input voltage range: 3.8–4.6 VDC; Constant current mode, continuous, |
| Short-Circuit Protection | self-recovery (Input voltage range) |
| Aislamiento (entrada–salida) | VDC (Electric Strength test for 1 minute with a) |
| Aislamiento | 6000 VDC |
| Resistencia de aislamiento | Input-output Resistance at 500VDC: 1000 MΩ |
| Capacidad de aislamiento | 24 pF (Input-output capacitance at 100kHz/0.1V) |
| Operating Ambient Temperature | -40 to +70℃ (See Fig. 1) |
| Temperatura de almacenamiento | -55–+125℃ |
| Humedad de almacenamiento | 5–95 %RH (Non-condensing) |
| Dimension | 58.00x 18.00 x 7.60 mm |
| Peso | 7.00g (Typ.) |
| Cooling method | Free air convection |
| CE | CISPR32/EN55032 CLASS B (see Fig.4 for recommended circuit) |
| RE | CISPR32/EN55032 CLASS B (see Fig.4 for recommended circuit) |
| ESD | IEC/EN61000-4-2 Contact ±4kV perf. Criteria B |
| RS | IEC/EN61000-4-3 10V/m (see Fig.4 for recommended circuit) perf. Criteria B |
| EMS EFT | IEC/EN61000-4-4 100KHz, ±2kV (see Fig.4 for recommended circuit) perf. Criteria B |
| Surge | IEC/EN61000-4-5 line to line ±1kV (see Fig.4for recommended circuit) perf. Criteria B |
| CS | IEC/EN61000-4-6 3 Vr.m.s (see Fig.4 for recommended circuit) perf. Criteria B |
| Typical Performance | Curves; Fig. 1 |
| All DC-DC converters of this | series are tested before delivery using the recommended circuit shown in Fig. 2.; Parameter description:; Cin 100uF/100V; Cout 2200uF/35V; Fig. 2 |
| 2. Model Control | recommended circuit |
| When control is enabled, the | voltage of the enable signal S1 is relative to the input pin GND.; Fig. 3 |
| 3. EMC compliance | circuit |
| Fig. 4 | Notes: We use Part ① in Fig. 4 for Immunity tests and Part ② for Emissions test. Selecting based on needs. |
| Parameter description: | FUSE Select according to the actual input current of the customer; MOV 14D101K; C01、C02 330uF 200V aluminum electrolytic capacitor; C03 100uF 100V aluminum electrolytic capacitor; CY1、CY2 2.2uF/400VDC; LDM1 6.8uH Differential mode inductance; C1、C2 4.7uF/100V; 4.7mH ( We recommend using our common mode inductor; LCM1; FL2D-30-472 differential mode inductor ) |
| 4. The product does not | support hot swap |
| 5. For additional information | please refer to DC-DC converter application notes on |
| Dimensions and | Recommended Layout |